818999
4
Zoom out
Zoom in
Previous page
1/135
Next page
1 DESCRIPTION
1.1 PURPOSE
This machine is intended for cutting and trimming hedges and
bushes in commercial use. It is not intended to be used for
cutting above shoulder level.
1.2 OVERVIEW
Figure 1
1Speed control button
2Trigger
3Rear handle
4Rotating button
5Blade
6Guard
7Front handle
8Activation switch
9power button
10 Anti-jamming button
2 SAFETY
WARNING
Make sure that you do/obey all safety instructions.
Refer to Safety Manual.
3 INSTALLATION
3.1 UNPACK THE MACHINE
WARNING
Make sure that you correctly assemble the machine before
use.
WARNING
If the parts are damaged, do not use the machine.
If you do not have all the parts, do not operate the
machine.
If the parts are damaged or missing, speak to the service
center.
1. Open the package.
2. Read the documentation in the box.
3. Remove all the unassembled parts from the box.
4. Remove the machine from the box.
5. Discard the box and package in compliance with local
regulations.
3.1.1 INSTALL THE BLADE ASSEMBLY
Figure 5.
1. Put the machine on a flat and smooth surface.
2. Slide the blade assembly (15) into the rotating shaft (17).
3. Insert the bolts and tighten with a screwdriver (not
included).
3.1.2 CONNECT THE BATTERY PACK TO
THE MACHINE
Figure 2.
1. Insert the plug (11) of one side of the cable into the
socket (12) in the machine – line up the lugs on the plug
with the slots in the socket.
2. Push the plug into the socket until it stops, then turn it
clockwise until the plug’s latch engages audibly.
3. Insert the plug (13) of the other side of the cable into the
socket (14) in the battery – line up the lugs on the plug
with the slots in the socket.
4. Push the plug into the socket until it stops, then turn it
clockwise until the plug’s latch engages audibly.
4 OPERATION
Touch the blade carefully.
Do not put your fingers into the notches or in position
where they can get cut.
Do not touch the blade unless you remove the battery
pack.
Do not use the machine if the blade is damaged or bent.
Remove all objects such as cords, lights, wire, or string
which can become entangled in the cutting blade and
create a risk of personal injury.
WARNING
If the blade jams on an electrical cord or line, DO NOT
TOUCH THE BLADE! IT CAN BE LIVE AND
DANGEROUS. Do the steps below:
1. Hold the insulated rear handle or put the machine down
and away from you.
2. Disconnect the battery from the battery pocket. Then
disconnect the cable before removing it from blade.
5 OPERATION
Touch the blade carefully.
Do not put your fingers into the notches or in position
where they can get cut.
Do not touch the blade unless you remove the battery
pack.
Do not use the machine if the blade is damaged or bent.
Remove all objects such as cords, lights, wire, or string
which can become entangled in the cutting blade and
create a risk of personal injury.
4
English
EN
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cramer 82HD62 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cramer 82HD62 in the language / languages: All languages as an attachment in your email.

The manual is 2.16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info