818996

Cramer 82CS34 Manual

7
Zoom out
Zoom in
Previous page
1/244
Next page
1. Cut the first time 1/3 of the diameter from the
bottom.
2. Cut the second time from the top to complete the
bucking.
• When the log is held on two ends,
1. Cut the first time 1/3 of the diameter from the
top.
2. Cut the second time lower 2/3 from the bottom to
complete the bucking.
• When the log is on a slope,
1. Stand on the uphill side.
2. Control the chainsaw.
3. Hold the handles tightly.
4. Release the cut pressure near the end of the
cut.
NOTE
Do not let the chain touch the ground.
When bucking is complete,
1. Release the trigger.
2. Stop the chainsaw fully.
3. Move the chainsaw from tree to tree.
5 MAINTENANCE
CAUTION
Do not let brake fluids, gasoline, petroleum-based
materials touch the plastic parts. Chemicals can
cause damage to the plastic, and make the plastic
unserviceable.
CAUTION
Do not use strong solvents or detergents on the plastic
housing or components.
WARNING
Remove the battery pack from the machine before
maintenance.
5.1 ADJUST THE CHAIN TENSION
Figure 2-7
The more you use a chain the longer it becomes. It is
therefore important to adjust the chain regularly to take
up the slack.
Tension the chain as tightly as possible, but not so tight
that you cannot pull it round freely by hand.
WARNING
A slack chain may jump off and cause serious or even
fatal injury.
CAUTION
Wear protective gloves if you touch the chain, bar or
areas around the chain.
1. Stop the machine.
2. Loosen the sprocket cover nuts with the wrench.
NOTE
It is not necessary to remove the sprocket cover to
adjust the chain tension.
3. Turn the chain tension adjuster clockwise to
increase the chain tension.
4. Turn the chain tension adjuster counterclockwise to
decrease the chain tension.
5. When the chain is at the wanted tension, tighten the
sprocket cover nuts.
6. Pull the chain in the middle of the guide bar at the
bottom away from the bar. The gap between the
chain guide and the guide bar should be between 3
mm and 4 mm.
5.2 ADJUST THE LUBRICANT
AMOUNT
Figure 23.
Adjust the lubricant amount with the wrench according
to the cutting requirement.
1. Find the adjustment screw at the bottom of the
machine.
2. Turn the screw clockwise to increase the lubricant
amount.
3. Turn the screw counterclockwise to decrease the
lubricant amount.
5.3 SHARPEN THE CUTTERS
Sharpen the cutters if it is not easy for the chain to go
into the wood.
NOTE
We recommend that your dealer, which has an electric
sharpener, perform important sharpening work.
Figure 16-19
1. Tensioning chain.
2. Sharpen the cutters corner with a 4.5 mm diameter
round file .
3. Sharpen the top plate, side plate and depth gauge
with a flat file.
4. File all the cutters to the specified angles and the
same length.
7
English EN
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cramer 82CS34 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cramer 82CS34 in the language / languages: All languages as an attachment in your email.

The manual is 3.77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info