818996

Cramer 82CS34 Manual

5
Zoom out
Zoom in
Previous page
1/244
Next page
1. Loosen and remove the cap from the oil tank.
2. Put the oil into the oil tank.
3. Monitor the oil indicator to make sure that no dirt
enters in the oil tank while you add the oil.
4. Put the oil cap on.
5. Tighten the oil cap.
6. A completely filled oil tank will last for 15 - 40
minutes operating time.
IMPORTANT
Do not use dirty, used or contaminated oil. Damage
can occur to the bar or chain.
3.3 ASSEMBLE THE GUIDE BAR AND
THE CHAIN
Figure 1-7.
1. Remove the chain cover nuts with the wrench.
2. Remove the chain cover.
3. Put the chain drive links into the bar groove.
4. Put the chain cutters in the direction of the chain
operation.
5. Put the chain in position and make sure that the
loop is behind the guide bar.
6. Hold the chain and bar.
7. Put the chain loop around the sprocket.
8. Make sure the chain tension pin hole on the guide
bar fits correctly with the bolt.
9. Install the chain cover.
10. Tighten the chain. Refer to Adjust the chain tension.
11. Tighten the nuts when the chain is well tensioned.
NOTE
If you start the chain saw with a new chain, have a
test for 2-3 minutes. A new chain gets longer after the
first use, examine the tension and tighten the chain if
necessary.
3.4 INSTALL THE BATTERY PACK
Figure 2
WARNING
• If the battery pack or charger is damaged, replace
the battery pack or the charger.
• Stop the machine and wait until the motor stops
before you install or remove the battery pack.
• Read, understand, and follow the instructions in
the battery and charger manual.
1. Align the lift ribs on the battery pack with the
grooves in the battery compartment.
2. Push the battery pack into the battery compartment
until the battery pack locks into place.
3. When you hear a click, the battery pack is installed.
3.5 REMOVE THE BATTERY PACK
Figure 2
1. Push and hold the battery release button.
2. Remove the battery pack from the machine.
4 OPERATION
NOTE
Remove the battery pack and keep hands clear of the
lock out button when you move the machine.
IMPORTANT
Examine the chain tension before each use.
4.1 EXAMINE THE CHAIN
LUBRICATION
NOTE
Do not use the machine without sufficient chain
lubrication.
Figure 1
1. Examine the lubricant level of the machine from the
oil indicator.
2. Add more lubricant if it is necessary.
4.2 HOLD THE MACHINE
Figure 8
1. The grip area is within 100 mm behind the lock out
button.
2. Hold the chainsaw with one hand at the rear handle
and with the other hand at the front handle. Always
use both hands when using the machine.
3. Hold the handles with the thumbs and the fingers
around them.
4. Make sure that the thumb of the hand that holds the
front handle is below the handle.
4.3 START THE MACHINE
Figure 1
1. Press the on/off switch.
2. Press the lock-out button.
3. Press the trigger while you hold the lock-out button.
4. Release the lock-out button.
5
English EN
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cramer 82CS34 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cramer 82CS34 in the language / languages: All languages as an attachment in your email.

The manual is 3.77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info