818995

Cramer 82CS25 Manual

9
Zoom out
Zoom in
Previous page
1/309
Next page
9
cramer.eu
EN
OPPOSITE SIDE OF THE TREE FROM THE NOTCHING UNDERCUT)
(see Figure 10)
Make the felling back cut at least 50mm higher than the horizontal notching cut.
Keep the felling back cut parallel to the horizontal notching cut.Make the felling
back cut so as to leave enough wood to act as a hinge. The hinge wood keeps the
tree from twisting and falling in the wrong direction.Do not cut through the hinge.
As the felling cut gets close to the hinge, the tree should begin to fall. If there is
any chance that the tree may not fall in the desired direction or it may rock back
and bind the saw chain, stop cutting before the felling back cut is complete and
use wedges of wood, plastic or aluminium to open the cut and drop the tree along
the desired line of fall. When the tree begins to fall, remove the chain saw from
the cut, stop the motor, put the chain saw down, and then use the retreat path as
planned. Be alert of overhead limbs falling and watch your footing.
Limbing a tree (see Figure 11)
Limbing is removing the branches from a fallen tree. When limbing, leave the larger
lower limbs to support the log off the ground. Remove the small limbs in one cut.
Branches under tension should be cut from the bottom up, to avoid binding the
chain saw.
Bucking a log (see Figure 12-15)
Bucking is cutting a log into lengths. It is important to make sure your footing is
firm and your weight is evenly distributed on both feet. When possible, the log
should be raised and supported by the use of limbs, logs or chocks.
Follow the simple direction for easy cutting:
•When the log is supported along the entire length, it is cut from the top
(over buck).
•When the log is supported on one end, cut 1/3 of the diameter from the
underside (under buck). Then make the finished cut by over bucking to
meet the first cut.
•When the log is supported on both ends, cut 1/3 of that diameter from the
top (over buck). Then make the finished cut by under bucking the lower 2/3
to meet the first cut.
•When bucking on a slope, always stand on the uphill side of the log. When
cutting through, to maintain complete control, release the cutting pressure
near the end of the cut without relaxing your grip on the chain saw handles.
Do not let the chain contact the ground. After completing the cut, wait for the
saw chain to stop before you move the chain saw. Always stop the motor before
moving from tree to tree.
MAINTENANCE
WARNING!
Always remove the battery pack from the machine before
checking the chain tension or making adjustments to the chain.
Wear protective gloves while touching the chain, bar or areas
around the chain.
Adjusting the chain tension (see Figure 2-7)
•Loosen the chain cover lock nuts with the supplied wrench. The chain cover
lock nuts do not have to be completely removed in order to adjust the chain
tension.
•Rotate the chain adjustment screw clockwise to increase the chain tension
and rotate counterclockwise to decrease the chain tension.
•Once the chain is at the desired tension, tighten the chain cover lock nuts.
Replacing the bar and chain (see Figure 3-7)
•Remove the battery from the chain saw.
•Remove the two chain cover lock nuts from chain cover by rotating them
counterclockwise with the wrench.
•Remove the chain cover from the mounting surface.
•The bar and chain can now be removed by lifting it away from the main
body of the saw and releasing the chain from the sprocket.
•Remove the old chain from the bar.
•Lay out the new saw chain in a loop and straighten any kinks. The cutters
should face in the direction of chain rotation. If they face backwards, turn
the loop over.
•Place the chain drive links into the bar groove.
•Position the chain so there is a loop at the back of the bar.
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cramer 82CS25 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cramer 82CS25 in the language / languages: All languages as an attachment in your email.

The manual is 5.31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info