818994

Cramer 82CS24 Manual

6
Zoom out
Zoom in
Previous page
1/236
Next page
IMPORTANT
The chain brake must be disengaged for the chain
saw to start. Activate the brake by moving the front
hand guard forwards.
4.4 STOP THE MACHINE
Figure 1.
1. Release the trigger to stop the machine.
4.5 OPERATE THE CHAIN BRAKE
WARNING
Make sure that your hands are on the handles at all
times.
Figure 22
1. Start the machine.
2. Turn your left hand around the front handle to
engage the chain brake.
3. Pull the front hand guard / chain brake toward the
front handle to disengage the chain brake.
4. Call approved your dealer for repair before use if
• The chain brake does not stop the chain
immediately.
• The chain brake does not stay in the disengaged
position without aid.
4.6 FELL A TREE
Figure 9-10.
It is recommended that the first-time user should, as
a minimum practice, cutting logs on a saw-horse or
cradle.
Before you start to fell a tree, make sure that
• The minimum distance between the areas of
bucking and felling is two times the height of the
tree.
• The operation does not
• Cause injury to personnel.
• Hit utility lines. If the tree touches utility lines,
immediately tell the utility company.
• Cause losses in property.
• The user is not in the dangerous area, for example,
the downhill side of the area.
• The escape paths that extend back and diagonally
behind the felling direction are clear. The felling
direction is controlled by
• The natural lean of the tree.
• The location of larger branches.
• The wind direction.
• There are no dirt, stones, loose bark, nails, and
staples on the tree.
1. Make a lower level notching cut. Make sure that
this cut is
a) 1/3 width of the diameter of the tree.
b) Perpendicular to the felling direction.
CAUTION
The level notching cut helps prevent pinching of
the saw chain or the guide bar when you make the
second notch.
2. Make the felling cut no less than 50 mm and
higher than the level notching cut. Make sure
that this cut
a) Is parallel to the level notching cut.
b) Keeps sufficient wood to become a hinge which
prevents the tree from twisting and felling to the
wrong direction.
When the felling cut gets near the hinge, the tree
falls. Stop the felling cut if the tree
• Does not fall to the correct direction or
• Moves backwards, causing the cutting bar and
chain to become stuck in the cut.
3. Use felling wedge to open the cut and let the tree
fall to the correct direction.
4. When the tree starts to fall,
a) Remove the chainsaw from the cut.
b) Stop the machine.
c) Put the machine down.
d) Go away through the escape path. Be careful
with overhead branches and your footing.
4.7 LIMB A TREE
Figure 11.
Limbing is to remove the branches from a fallen tree.
1. Keep the larger lower branches to hold the log off
the ground.
2. Remove the small limbs in one cut.
3. Limb the branches with tension from the bottom to
up.
4. Keep the larger lower branches as a support until
the log is limbed.
4.8 BUCK A LOG
Figure 12-15.
Bucking is to cut a log into lengths. Keep your body
balance. If it is possible, lift the log and hold it with
branches, logs or chock.
• When the log is held along the full length, cut it from
the top.
• When the log is held on one end,
6
English
EN
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cramer 82CS24 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cramer 82CS24 in the language / languages: All languages as an attachment in your email.

The manual is 4.45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info