818994
4
Zoom out
Zoom in
Previous page
1/236
Next page
1 DESCRIPTION
1.1 PURPOSE
This chainsaw is designed for cutting branches, trunks,
logs and beams of a diameter determined by the cutting
length of the guide bar. It is only designed to cut wood.
1.2 OVERVIEW
Figure 1-22
1Guide bar cover
2Front handle
guard / chain brake
3Front handle
4On/Off switch
5Lock out button
6Trigger
7Oil tank cap
8Oil indicator
9Spike bumpers
10 Saw chain
11 Guide bar
12 Rear handle
13 Chain tension
screw
14 Chain cover
15 Chain cover nuts
16 Bolt for saw chain
tension
17 Sprocket
18 Battery release
button
19 Oil outlet
20 Bar groove
21 Chain drive links
22 Cutter
23 Felling direction
24 Danger zone
25 Escape route
26 Direction of fall
27 Notch
28 Felling back cut
29 Hinge
30 Limb cut
31 Keep work off
ground leave
support limbs until
log is cut
32 Log supported
along the entire
length
33 Cut from top (over
buck) avoid cutting
earth
34 Log supported one
end
35 Under buck
36 Over buck
37 Log supported both
ends
38 Bucking a log
39 Stand on uphill
side when cutting
because log may
roll
40 Wrench
2 GENERAL SAFETY
WARNINGS
WARNING
Read all safety warnings, instructions, illustrations
and specifications provided with this machine.
Failure to follow all instructions listed below may result
in electric shock, fire and/or serious injury.
Save all warnings and instructions for future
reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
3 INSTALLATION
WARNING
Do not change or use accessories that are not
recommended by the manufacturer.
WARNING
Do not install battery pack until you assemble all the
parts.
3.1 UNPACK THE MACHINE
WARNING
Make sure that you correctly assemble the machine
before use.
WARNING
If parts of the machine are damaged, do not use
the machine.
If you do not have all the parts, do not operate the
machine.
If parts are damaged or missing, contact the
service center.
1. Open the package.
2. Read the documentation provided in the box.
3. Remove all the unassembled parts from the box.
4. Remove the machine from the box.
5. Discard the box and packing material in compliance
with local regulations.
WARNING
For your personal safety, do not insert battery before
the tool is assembled completely.
3.2 ADD THE BAR AND CHAIN
LUBRICANT
Examine the amount of oil in the machine. If the oil level
is low, add the bar and chain lubricant as follows.
IMPORTANT
Use bar and chain lubricant that is only for chains and
chain oilers.
NOTE
The machine comes from the factory without bar and
chain lubricant.
4
English
EN
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cramer 82CS24 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cramer 82CS24 in the language / languages: All languages as an attachment in your email.

The manual is 4.45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info