818997

Cramer 48CS18 Manual

6
Zoom out
Zoom in
Previous page
1/240
Next page
NOTE
Do not let the chain touch the ground.
When bucking is complete,
1. Release the trigger.
2. Stop the chainsaw fully.
3. Move the chainsaw from tree to tree.
5 MAINTENANCE
CAUTION
Do not let brake fluids, gasoline, petroleum-based materials
touch the plastic parts. Chemicals can cause damage to the
plastic, and make the plastic unserviceable.
CAUTION
Do not use strong solvents or detergents on the plastic
housing or components.
WARNING
Remove the battery pack from the machine before
maintenance.
5.1 ADJUST THE CHAIN TENSION
Figure 2-7
The more you use a chain the longer it becomes. It is
therefore important to adjust the chain regularly to take up the
slack.
Tension the chain as tightly as possible, but not so tight that
you cannot pull it round freely by hand.
WARNING
A slack chain may jump off and cause serious or even fatal
injury.
CAUTION
Wear protective gloves if you touch the chain, bar or areas
around the chain.
1. Stop the machine.
2. Loosen the sprocket cover nuts with the wrench.
NOTE
It is not necessary to remove the sprocket cover to adjust the
chain tension.
3. Turn the chain tension adjuster clockwise to increase the
chain tension.
4. Turn the chain tension adjuster counterclockwise to
decrease the chain tension.
5. When the chain is at the wanted tension, tighten the
sprocket cover nuts.
6. Pull the chain in the middle of the guide bar at the bottom
away from the bar. The gap between the chain guide and
the guide bar should be between 3 mm and 4 mm.
5.2 SHARPEN THE CUTTERS
Sharpen the cutters if it is not easy for the chain to go into the
wood.
NOTE
We recommend that your dealer, which has an electric
sharpener, perform important sharpening work.
Figure 16-19
1. Tensioning chain.
2. Sharpen the cutters corner with a 4.5 mm diameter round
file .
3. Sharpen the top plate, side plate and depth gauge with a
flat file.
4. File all the cutters to the specified angles and the same
length.
NOTE
During the process,
• Keep the file flat with the surface to be sharpened.
• Use the midpoint of the file bar.
• Use light but firm pressure when sharpening the
surface.
• Lift the file away on each return stroke.
• Sharpen the cutters on one side and then move to the
other side.
Replace the chain if:
• The length of the cutting edges is less than 5 mm.
• There is too much space between the drive links and the
rivets.
•The cut speed is slow
• Sharpening the chain many times but it does not increase
the cutting speed. The chain is worn.
5.3 GUIDE BAR MAINTENANCE
Figure 20-21.
NOTE
Make sure that it is turned over periodically to keep
symmetrical wear on the bar.
1. Lubricate the bearings on the nose sprocket (if present)
with the syringe (not included).
2. Clean the bar groove with the scraping hook (not
included).
3. Clean the lubrication holes.
4. Remove burr from the edges and level the cutters with a
flat file.
8
English
EN
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cramer 48CS18 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cramer 48CS18 in the language / languages: All languages as an attachment in your email.

The manual is 2.37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info