751453
33
Zoom out
Zoom in
Previous page
1/36
Next page
EN - 30
FAULT  
There is detergent residue
on your laundry after
washing
Non-dissolving particles of some
detergents may appear on your
laundry as white spots.
Perform an extra rinse, or clean your laundry with
a brush after it dries
There is detergent residue
on your laundry after
washing
There is untreated oil, cream or
laundry
Use the amount of detergent as instructed on the
packaging in the next wash
Spinning operation is not
performed or runs late.
No fault. The Unbalanced load
control system has been activated.
The Unbalanced load control system will try
to spread your laundry evenly. The spinning
operation will begin once your laundry is evenly
spread.
Place the laundry in the machine in a balanced
fashion next time.
Laundry remains damp after
the drying operation.
Appropriate drying programme
is not selected. The maximum
load capacity for the selected
programme might be exceeded.
Select a drying programme appropriate for your
laundry (see page 21 for the programme table)
12. AUTOMATIC FAULT WARNINGS AND WHAT NEEDS TO BE DONE
Your machine is equipped with a built-in fault detection system, indicated by a combination
of flashing wash operation lights. The failure codes are shown below.
  WHAT TO DO
E01 The door of your machine is left open.
Shut the door properly unitl you hear the click. If the
fault persists, turn off your machine, unplug it and
contact the nearest authorised service immediately.
E02 The water pressure or the water level
inside the machine is low.
Check that the cold water tap is fully turned on and
that mains water is not cut-off. If the fault persists,
your machine will stop automatically. Unplug the
machine, turn off the cold water tap and contact the
nearest authorised service.
E03
The pump is faulty or pump filter is
clogged or electrical connection of the
pump is faulty.
Clean the pump filter. If the problem persists, contact
the nearest authorised service. (*)
E04 Your machine has excessive amount
of water.
Your machine will automatically drain the water. Turn
off your machine and unplug it. Turn off the cold water
tap and contact the nearest authorised service.

33


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Corbero CLSV961420T at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Corbero CLSV961420T in the language / languages: English as an attachment in your email.

The manual is 5,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Corbero CLSV961420T

Corbero CLSV961420T User Manual - Spanish - 36 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info