652338
46
Zoom out
Zoom in
Previous page
1/80
Next page
46 Operating the control software
5.5.2.1 Inputdiagnosticfunctions–"InputDiagnostics"submenu
The following input values can be viewed after accessing the "Input Diagnostics" submenu.
Note: the input values can be accessed and viewed too, via the "Service Info" selection eld in the
standard operating display.
Cylinder A Tab (Cylinder B Tab)
Note: the tabs of the input diagnostics for Cylinder B appear only on double units or large units with two
steam cylinders.
Channel 1: Set humidity setpoint in %rh for humidity contol.
Channel 2: Set humidity setpoint in %rh for supply air limitation.
Enable Input On/Off: Actual status of the external enable switch, if present
("Off"= switch open, "On"= switch closed).
Safety Loop: Actual status of the external safety chain ("Open"= safety
chain open, "Closed"= safety chain closed).
Level High: Actual status of the "Level High" detection ("Off"= Level is
not high, "On"= Level is high).
Level Mid: Actual status of the "Level Mid" detection ("Off"= Level is not
in the middle, "On"= Level is in the middle).
Level Low: Actual status of the "Level Low" detection ("Off"= Level is not
low, "On"= Level is low)
Leakage Sensor: Actual status of the optional leakage monitoring device
("Off"= no leakage present, "On"= leakage detected).
Overheat Switch: Actual status of the excess temperature switch on
the steam cylinder ("Open"= Excess temperature switch has triggered,
"Closed"= Excess temperature switch has not triggered).
Temperature Switch: Actual status of the of the temperature switch
("Open"= Temperature switch has triggered, "Closed"= Temperature switch
has not triggered).
Heating Voltage: Actual status of the heating voltage ("Off"= heating
voltage not activated, "On"= heating voltage activated).
Blower Pack: shows the status of the blower pack security loop (status
shows"Off" when the blower pack is connected and powered, and "On"
when it is not.
Note: When no blower pack is connected, a jumper wire must be installed
in the blower pack security loop, and the status should show "Off".
46


Need help? Post your question in this forum.

Forumrules
1

Forum

condair-rs

Reset search

  • why drain hose led to left, is it due to electrical on right side.
    Submitted on 29-8-2022 at 23:32

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Condair RS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Condair RS in the language / languages: English as an attachment in your email.

The manual is 5,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Condair RS

Condair RS Installation Guide - English - 80 pages

Condair RS User Manual - Dutch - 80 pages

Condair RS Installation Guide - Dutch - 76 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info