652338
63
Zoom out
Zoom in
Previous page
1/80
Next page
63Mounting and installation work
5.7.6 Installation work external connections
Connecting the external safety chain
B3
B2
B1
MAINS SUPPLY
L N SC1SC2PEPE
J3
K2
Control compartment
Do not apply extraneous
voltage via K2!
DANGER: 230 V
The potential-free contacts of external moni t or ing de-
vices (e.g. ventilation interlock "B1", airow monitor "B2",
safety high limit humidistat "B3", etc.) are connected in
series (safety chain "K2") to the terminals "SC1" and
"SC2" of the terminal block "X1" on the driver board in
accordance with the wiring diagram.
The connecting cable must be led through a cable gland
into the control compartment.
Caution! A high limit humidistat is highly recomen-
ded to prevent risk of over-humidication and potential
damage to property.
Note: If, for whatever reason, no external monitoring de-
vices are connected, a jumper wire "J3" must be installed
on the contacts "SC1" and "SC2" of the terminal block.
CAUTION! Do not apply any extraneous voltage to
contacts "SC1" and "SC2" via the contacts of the
external monitoring devices.
Humidity control wiring
Connecting a demand or humidity signal
CONTROL
V+ IN GND
JP2 (24V)
JP1 (10V)
+
A1
Y
24V/
10V
Control compartment
The signal cable of an external controller or of a humid-
ity sensor (if the internal P/PI controller is used) are to
be connected according to the wiring diagram to the
terminals "IN" and GND" on the driver board in the
control compartment. The connecting cable must be
led through a cable gland into the control compartment.
Note: if the external controller or the humidity sensor
shall be supplied with 10 V or 24 V from the driver board
(terminal “A+”), the jumper JP1 must be set to 10V or
24V accordingly.
Note: the humidity control must be congured via the
control software accordingly. The admissible humidity
control signal values can be found in the technical data
table in the operation manual.
If a shielded signal cable is used, connect the shielding
to terminal "GND".
Caution! If the shielding of the control signal is already
connected to a po ten tial or a grounded conductor,
do not connect it to terminal "GND"
63


Need help? Post your question in this forum.

Forumrules
1

Forum

condair-rs

Reset search

  • why drain hose led to left, is it due to electrical on right side.
    Submitted on 29-8-2022 at 23:32

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Condair RS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Condair RS in the language / languages: English as an attachment in your email.

The manual is 7,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Condair RS

Condair RS User Manual - English - 80 pages

Condair RS User Manual - Dutch - 80 pages

Condair RS Installation Guide - Dutch - 76 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info