804417

Concept CP2000 Manual

30
Zoom out
Zoom in
Previous page
1/71
Next page
1. Connect the steam cleaner into the mains. Press the power on/
off button, the indicator will light blue.
2. After a few seconds half of the indicator will tum red, meaning the
appliance is ready for use.
3. Put your foot on the head and angle the body of the cleaner downwards
(6).
4. Press the trigger to release the vapour (7).
5. Move the cleaner slowly backwards and forwards paying particular
attention to frequently used areas.
CARPET CLEANING
NOTE: Always vacuum or sweep the floor prior to use the steam cleaner.
IMPORTANT: Do not use the cleaner without the Textile Pad attached to
the Head.
1. Attach the Carpet Glider to the Head (10).
2. Connect the steam cleaner into the mains. Press the power on/off
button, the indicator will light blue.
3. After a few seconds half of the indicator will tum red, meaning the
appliance is ready for use.
4. Put your foot on the head and angle the body of the cleaner downwards
(6).
5. Press the trigger to release the vapour (7).
6. Move the cleaner slowly backwards and forwards paying particular
attention to frequently used areas.
MANUAL CLEANER OPERATION
1. Press the Manual Cleaner Release Button and remove the steel tube
(11).
2. Remove the Head (12).
3. Press the Water Tank Release Button and remove the Water Tank (3).
NOTE:A tube feeding water from the water tank to the boiler is loaded with
a brass ball. This design is intentional and serves to increase the efficiency
of water use. It is normal for this ball to create a rattling sound inside the
Water Tank during operation.
4. Pull the Water Tank by the cap and open it (4).
5. Fill the tank with cold tap water. Secure the tank with the cap (4). Do
not add any chemicals, detergents or perfumes to the Water Tank.
NOTE: We recommend to use distilled or de-mineralized water in order to
reduce building up mineral deposits and prolonging the life of the appliance.
EN
57CP 2000
6. Put the Water Tank back on the main part of the cleaner and make sure
the Water Filter is installed.
7. Connect the steam cleaner into the mains. Press the power on/
off button, the indicator will light blue.
8. After a few seconds half of the indicator will tum red, meaning the
appliance is ready for use.
9. Press the trigger to release the vapour (on the manual cleaner)(13).
IMPORTANT: Always disconnect the cleaner from the mains prior to
removing the Head or handling the appliance. Always ensure the cleaner
has fully cooled down before removing the Head.
SOLUTION TANK USE
1. Rotate the Solution Tank cap counter-clockwise to open and fill the tank
with a solution fluid (8).
2. Put back the Solution Tank cap and screw it clockwise.
3. Press the foot pedal to the ON position to engage the Solution Tank.
Press the foot pedal to the OFF position to disengage.
IMPORTANT:To prevent solution from leaking ensure the foot
pedal is in the OFF position when the product is not in use.
Empty the solution tank
1. Connect the steam cleaner into the mains. Press the power on/off
button, the indicator will light blue.
2. Remove the Solution Tank (17).
3. Rotate the Solution Tank cap counter-clockwise to open.
4. Pour out the solution from the tank (17).Put back the Solution Tank
cap, screw it clockwise, then put the tank back in its place.
EN
58 CP 2000
EN
58 CP2000
1. Connect the steam cleaner into the mains. Press the power on/
off button, the indicator will light blue.
2. After a few seconds half of the indicator will tum red, meaning the
appliance is ready for use.
3. Put your foot on the head and angle the body of the cleaner downwards
(6).
4. Press the trigger to release the vapour (7).
5. Move the cleaner slowly backwards and forwards paying particular
attention to frequently used areas.
CARPET CLEANING
NOTE: Always vacuum or sweep the floor prior to use the steam cleaner.
IMPORTANT: Do not use the cleaner without the Textile Pad attached to
the Head.
1. Attach the Carpet Glider to the Head (10).
2. Connect the steam cleaner into the mains. Press the power on/off
button, the indicator will light blue.
3. After a few seconds half of the indicator will tum red, meaning the
appliance is ready for use.
4. Put your foot on the head and angle the body of the cleaner downwards
(6).
5. Press the trigger to release the vapour (7).
6. Move the cleaner slowly backwards and forwards paying particular
attention to frequently used areas.
MANUAL CLEANER OPERATION
1. Press the Manual Cleaner Release Button and remove the steel tube
(11).
2. Remove the Head (12).
3. Press the Water Tank Release Button and remove the Water Tank (3).
NOTE:A tube feeding water from the water tank to the boiler is loaded with
a brass ball. This design is intentional and serves to increase the efficiency
of water use. It is normal for this ball to create a rattling sound inside the
Water Tank during operation.
4. Pull the Water Tank by the cap and open it (4).
5. Fill the tank with cold tap water. Secure the tank with the cap (4). Do
not add any chemicals, detergents or perfumes to the Water Tank.
NOTE: We recommend to use distilled or de-mineralized water in order to
reduce building up mineral deposits and prolonging the life of the appliance.
EN
57CP 2000
6. Put the Water Tank back on the main part of the cleaner and make sure
the Water Filter is installed.
7. Connect the steam cleaner into the mains. Press the power on/
off button, the indicator will light blue.
8. After a few seconds half of the indicator will tum red, meaning the
appliance is ready for use.
9. Press the trigger to release the vapour (on the manual cleaner)(13).
IMPORTANT: Always disconnect the cleaner from the mains prior to
removing the Head or handling the appliance. Always ensure the cleaner
has fully cooled down before removing the Head.
SOLUTION TANK USE
1. Rotate the Solution Tank cap counter-clockwise to open and fill the tank
with a solution fluid (8).
2. Put back the Solution Tank cap and screw it clockwise.
3. Press the foot pedal to the ON position to engage the Solution Tank.
Press the foot pedal to the OFF position to disengage.
IMPORTANT:To prevent solution from leaking ensure the foot
pedal is in the OFF position when the product is not in use.
Empty the solution tank
1. Connect the steam cleaner into the mains. Press the power on/off
button, the indicator will light blue.
2. Remove the Solution Tank (17).
3. Rotate the Solution Tank cap counter-clockwise to open.
4. Pour out the solution from the tank (17).Put back the Solution Tank
cap, screw it clockwise, then put the tank back in its place.
EN
58 CP 2000
EN
59CP2000
• CAUTION! Use only distilled water to ll the water tank!
• Always unplug the appliance when lling with distilled water, emptying
or when the appliance is not in use.
REPLACING THE WATER FILTER
The water lter helps to lter minerals contained in water that reduce
the eciency of the steam cleaner. Depending on the frequency of use
of the appliance, the lter should be replaced every 80–100 hours. Use
only distilled water in the steam mop. If you live in an area with hard
water, this water may cause deposits on the heater, which will reduce the
performance of the cleaner. Use only distilled water. This will extend the
service life of the water lter and heater.
1. Connect the steam cleaner into the mains. Press the power on/
off button, the indicator will light blue.
2. After a few seconds half of the indicator will tum red, meaning the
appliance is ready for use.
3. Put your foot on the head and angle the body of the cleaner downwards
(6).
4. Press the trigger to release the vapour (7).
5. Move the cleaner slowly backwards and forwards paying particular
attention to frequently used areas.
CARPET CLEANING
NOTE: Always vacuum or sweep the floor prior to use the steam cleaner.
IMPORTANT: Do not use the cleaner without the Textile Pad attached to
the Head.
1. Attach the Carpet Glider to the Head (10).
2. Connect the steam cleaner into the mains. Press the power on/off
button, the indicator will light blue.
3. After a few seconds half of the indicator will tum red, meaning the
appliance is ready for use.
4. Put your foot on the head and angle the body of the cleaner downwards
(6).
5. Press the trigger to release the vapour (7).
6. Move the cleaner slowly backwards and forwards paying particular
attention to frequently used areas.
MANUAL CLEANER OPERATION
1. Press the Manual Cleaner Release Button and remove the steel tube
(11).
2. Remove the Head (12).
3. Press the Water Tank Release Button and remove the Water Tank (3).
NOTE:A tube feeding water from the water tank to the boiler is loaded with
a brass ball. This design is intentional and serves to increase the efficiency
of water use. It is normal for this ball to create a rattling sound inside the
Water Tank during operation.
4. Pull the Water Tank by the cap and open it (4).
5. Fill the tank with cold tap water. Secure the tank with the cap (4). Do
not add any chemicals, detergents or perfumes to the Water Tank.
NOTE: We recommend to use distilled or de-mineralized water in order to
reduce building up mineral deposits and prolonging the life of the appliance.
EN
57CP 2000
6. Put the Water Tank back on the main part of the cleaner and make sure
the Water Filter is installed.
7. Connect the steam cleaner into the mains. Press the power on/
off button, the indicator will light blue.
8. After a few seconds half of the indicator will tum red, meaning the
appliance is ready for use.
9. Press the trigger to release the vapour (on the manual cleaner)(13).
IMPORTANT: Always disconnect the cleaner from the mains prior to
removing the Head or handling the appliance. Always ensure the cleaner
has fully cooled down before removing the Head.
SOLUTION TANK USE
1. Rotate the Solution Tank cap counter-clockwise to open and fill the tank
with a solution fluid (8).
2. Put back the Solution Tank cap and screw it clockwise.
3. Press the foot pedal to the ON position to engage the Solution Tank.
Press the foot pedal to the OFF position to disengage.
IMPORTANT:To prevent solution from leaking ensure the foot
pedal is in the OFF position when the product is not in use.
Empty the solution tank
1. Connect the steam cleaner into the mains. Press the power on/off
button, the indicator will light blue.
2. Remove the Solution Tank (17).
3. Rotate the Solution Tank cap counter-clockwise to open.
4. Pour out the solution from the tank (17).Put back the Solution Tank
cap, screw it clockwise, then put the tank back in its place.
EN
58 CP 2000
EN
59CP2000
ENEN
5958 CP2000 | CP2010CP2000 | CP2010
… 30 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Concept CP2000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Concept CP2000 in the language / languages: English, German, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 7.45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info