636221
27
Zoom out
Zoom in
Previous page
1/42
Next page
27
OPERATION WITH SWITCHING DEVICE ART. 1404 (DEFAULT)
OPERATION WITH SWITCHING DEVICE ART. 1405
In the configuration of Art. 1404, the MIN and MAX Dip switches define respectively the lowest and highest user codes
which can be connected to the riser. For information on setting the desired values, refer to the table on page 13. Separate
switching devices for dierent risers must manage code ranges which are not overlapping.
The self-ignition function is only available for systems as depicted in diagram MNK/017CQC (for each internal unit, it is
possible to toggle between the external unit of the KIT and the main external unit).
In “Main external unit” mode, lock release (or actuator) commands are only executed if the external unit is in call or self-ignition
mode. The “door-open” function is always deactivated.
In “Secondary external unit” mode, lock release (or actuator) commands are executed if the system is in standby mode or if the
external unit is active.
If the system is in standby mode the first self-ignition command will activate the camera of the secondary external unit. Further
commands will toggle between the external units, activating alternately the main external unit and the secondary external unit.
With the switching device Art. 1405 it is possible to install only 1 main external unit and 1 secondary external unit.
Additional door-entry phones Art. 2638
1. Privacy function indicator
2. Key button
3. Button P1 generic actuator / button for various uses
present on terminal block (P1 C1)
4. 3-position ringtone/Privacy service selector:
High position: Maximum ringtone volume.
Middle position: Medium ringtone volume.
Low position: Privacy service activation. (Privacy service
means exclusion of the call ringtone from the external
unit and switchboard; activation of the Privacy function is
signalled by a red indicator appearing at the top right-
hand side).
5. Trimmer for adjusting the microphone volume
6. U2 DIP switch for setting user code
7. System connection terminals:
L L bus line connection.
CFP CFP Floor door call input.
P1 C1 terminals for pushbutton P1 C.NO. 24V 100mA
dedicated to various services (remove CV1 and CV2).
S+ S- terminals for call repetition device
8. JP2 jumper for selecting the Switchboard call (position C)
/ Generic actuator (position A) function of button P1
9. CV1 CV2 jumpers to be removed in order to obtain a
voltage free C. NO contact on button P1
1
2
3
4
1
5
6
7
8
9
2
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Comelit 8461MB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Comelit 8461MB in the language / languages: English as an attachment in your email.

The manual is 9,01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info