521985
15
Zoom out
Zoom in
Previous page
1/24
Next page
CSB200 Class B AIS
R2.0 29
If the Red Error LED illuminates continuously the unit should be assumed
to be faulty and should either be switched off (power removed) or if this is
not practical any other vessel position information derived from the unit
should not be used and it should also be assumed that the unit is not
transmitting valid position information for your vessel.
The unit should be examined by an authorised service agent at the
earliest opportunity.
LED Indicators
ON
This is a green LED which indicates, when lit, that power has been
connected correctly to the transponder.
Status
This is a green LED which indicates, when lit, that the transponder
hardware has been configured, that the operating software is present,
that the CPU has booted up, the application software is running and
everything is correct.
RX
This is a green LED which indicates when flashing that the CSB200 is
receiving data from other AIS transponders and is outputting this data as
VDM NMEA sentences on the output data ports. If the Green LED is on
continuously the unit has not been programmed with its personalised
data. It will still send received data to the output port, but will not transmit.
TX
This is a red LED which flashes momentarily when the CSB200 transmits
its own AIS data.
Timeout
This is a yellow LED which indicates when lit that the transmitter is
prevented from transmitting. Reasons for this include the following:
The transponder’s internal GPS receiver is not operating or is
not yet ready.
CSB200 Class B AIS
R2.0 30
The transponder was unable to transmit an AIS message due to
the channel being already occupied, e.g. by transmissions from
other AIS transponders, or the TX Off function is in operation.
Error
This is a red LED which indicates, when lit, one of the following status
conditions is possible:
Transmitter lockout timer (1 second maximum) has operated
GPS is unable to gain lock after 30 minutes
VHF antenna VSWR is out of range
Power Supply is out of range
Background noise level is above the threshold level (-77dBm)
Transmit Off Facility.
The Blue LED can be configured to operate in 3 modes by the proAIS
program:
Switch has no function, default mode as supplied.
Silent mode facility is provided in the event that you do not wish
to disclose your position to other users or to conserve power
when it is not necessary to transmit your position. The
transmitter can be turned off by connecting a simple ON/OFF
switch between the Blue cable on pin 6 and the Green cable on
pin 5. Closing this switch will cause the Blue-TX off LED and
the Yellow Timeout LED to light, the Green Status LED will
extinguish. Opening the switch will resume transmissions.
Reception of AIS data during this operation will not be affected.
Send Safety Related Message will send a Type 14 message
with your MMSI number and the words MAYDAY MAYDAY. The
message can be turned on by connecting a momentary push on
button between the Blue cable on pin 6 and the Green cable on
pin 5. Holding the switch down for 3 seconds will activate the
function and cause the blue LED to light, it will stay illuminated
for 1 minute, further pushes of the switch, after the Blue LED
extinguishes, will repeat the message.
www.Busse-Yachtshop.de email: info@busse-yachtshop.de
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Comar CSB200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Comar CSB200 in the language / languages: English as an attachment in your email.

The manual is 0,54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info