669018

Cola TERMO POWER 30S Manual

57
Zoom out
Zoom in
Previous page
1/175
Next page
T-POWER30_T-POWER 30S
57
When the water temperature has reached the set value,
as a condition also at the same time as that described in par.4.4.1,
the output is automatically brought to the min. value,
MODULATION status.
As for idro model stove, when the water temperature parameter
can’t be reached, the activation of led [ A ] starts.
4.4.3 Restart from STANDBY
After shutdown, the stove goes to cooling status, bringing the fume
extractor speed to the set value for brazier cleaning. Relighting
occurs as soon as the room temperature reach the SET value.
4.4.4 Cleaning the brazier
During normal operation in work mode, the 'BRAZIER CLEANING'
mode is activated at fixed intervals for a set duration.
4.4.5
Water heater with heat exchanger quickly
When hot water is required, the display shows the word SCAM HEALTH and LED lights shown from the tap. The
function, however, is only executed if the stove is lit, and has reached a sufficient temperature inside the camera.
In the remaining cases the service is not provided.
4.4.6 Water heater with storage tank
This type of installation requires the use of an external thermostat, which measures the temperature of the water of
the kettle. When the temperature drops below the set temperature of SET in the external thermostat activates the
function of health, the display shows the message of the stove and boiler HEALTH LED lights shown from the tap
until the request is satisfied.
If the stove is in the HOLD step REQUEST automatically turns on and you put in WORK. Once the temperature of
water in the camera work, you turn the water supply to the boiler.
SET When the temperature of the tank is met, the oven converts waste heat to the heating for about 2 minutes and
then, if there is another request, it waits or REQUEST MODULATION, according to the settings ( see prg. 4.6.5).
If the stove is in the OFF state, no lights and does not provide the service.
4.4.7 System with puffer / heat storage
This type of installation requires the use of an external thermostat, which measures the temperature of the puffer.
When the temperature is lowered below the temperature of SET set in the external thermostat, in the stove display
shows the message WATER PUFFER or BOILER WATER and light up the 2 LEDs respectively indicated by the tap
and from the radiator as it can meet the plant heating system.
If the stove is in the HOLD step REQUEST automatically turns on and goes into WORK and reached the working
temperature of the water in the camera, you turn the water supply to the puffer.
SET When the temperature of the puffer is satisfied, the stove is placed in a HOLD REQUEST (it is recommended to
set the function ON STAND-BY, see prg. 4.6.5).
If the stove is in the OFF state, no lights and does not provide the service.
Dialogue box
Clock
Room temperature
Water temperature
Dialogue
Clock
Set output
A
… 57 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cola TERMO POWER 30S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cola TERMO POWER 30S in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 9,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info