634273

Cobra MX46SPE Manual

14
Zoom out
Zoom in
Previous page
1/18
Next page
- 14 -
CAUTION! The equipment is suitable for use only in a power supply with permissible modulus of
system impedance is 0.237Ω or less.
10.2 CONNECTION FOR AUTO DRIVE – SELF PROPELLED
Grip the Self-drive control handle, the lawnmower will move forward automatically with about 3.6km/h,
release the self-drive handle, the lawnmower will stop moving.
Fig.9
CAUTION: your mower is designed to cut normal residential grass of a height no more than 250mm.
Do not attempt to mow through unusually tall dry or wet grass (e.g., pasture) or piles of dry leaves.
10.3 FOR THE BEST RESULTS WHEN MOWING
Clear lawn of debris: Be sure that the lawn is clear of stones, sticks, wire or other objects, which could be
accidentally thrown out by the mower in any direction and cause serious injury to the operator and others as
well as damage to property and surrounding objects.
Avoid cutting wet grass: For effective mowing do not cut wet grass, because it tends to stick to the
underside of the deck preventing proper mowing of the grass clippings.
General Recommendations: Cut no more than 1/3 the length of the grass. The recommended cut for
mowing is 1/3 the length of the grass. Ground speed will need to be adjusted so the clippings can be
dispersed evenly into the lawn. For especially heavy cutting in thick grass it may be necessary to use one of
the slowest speeds in order to get a clean well mowed cut. When mowing long grass you may have to cut the
lawn in two passes, lowering the blade another 1/3 of the length for the second cut and perhaps cutting in a
different pattern than was used the first time. Overlapping the cut a little on each pass will also help to clean
up any stray clippings left on the lawn. The mower should always be operated at full throttle to get the best
cut and allow it to do the most effective job of mowing.
Clean underside of deck: Be certain to clean the underside of the cutting deck after each use to avoid a
build-up of grass, which would prevent proper mulching. Mowing leaves. The mowing of leaves can also be
beneficial to your lawn. When mowing leaves make sure they are dry and are not laying too thick on the lawn.
Do not wait for all the leaves to be off the trees before you mow.
WARNING: if the mower blade strikes a foreign object, then stop the engine. Disconnect the plug from the
wall socket, thoroughly inspect the mower for any damage and repair the damage before restarting and
operating the mower. Extensive vibration of the mower during operation is an indication of serious damage.
The unit should be promptly inspected and repaired.
11. BLADE
The blade is made of pressed steel. It will be necessary to reshape it frequently (with a grinding wheel).
Ensure that it is always balanced (an unbalanced blade will cause dangerous vibrations). To check for
balance, insert a round rod through the central hole and support the blade horizontally. A balance blade will
remain horizontal. If the blade is not balanced the heavy end will rotate downwards. Reshape the heavy end
until the blade is currently balanced. To remove the blade (2), unscrew the blade screw (3).
Check the conditions of the fan (1), and replace any parts, which are damaged.
When reassembling, make sure that the cutting edges face in the direction of the motor rotation. The blade
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cobra MX46SPE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cobra MX46SPE in the language / languages: English as an attachment in your email.

The manual is 0,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info