773865
7
Zoom out
Zoom in
Previous page
1/12
Next page
3.4 AUTOMATIC MODE (continued)
How to select and carry out custom programming.
a) Press the 'OK/mode' button.
b) Select the auto mode by pressing the button until (Automatic Mode) is displayed and press the
'OK/mode' button to confirm.
c) The display will now show the set temperature together with a red dot that indicates the unit is working in
automatic mode. If the unit has been programmed previously then it may show
d) Press the 'OK/mode' button for a few seconds until (Configure Time) is displayed.
e) Press the button and then press the 'OK/mode' button on (Select Day).
f) Press and buttons to select the day you wish to change the on/off times and then press the 'OK/mode'
button.
g) The display now shows or or depending on how it was previously programmed.
The indicates the time in hours, i.e. =12:00am, =01:00am and so on.
h) By using the and buttons you can select (OFF), (ECO) or (ON) for that time period.
Once selected Press the 'OK/mode' button to move onto the next time period.
i) Repeat step h) until you go through all the 24 hours. The display will now show allowing
you to select the next day to program. Press the 'OK/mode' button and continue from step f) if you wish to
program each day individually. Alternatively you can copy one day to the next by following steps in section
3.5 COPY FUNCTION step b).
3.5 COPY FUNCTION
This function enables you to copy a previously programmed day to any other day. i.e. day1 to day2 or day1 to
day5, etc.
To copy the setting of one day into another, do as follows:
a) Press the 'OK/mode' button for a few seconds until (Configure Time) is displayed.
b) Press button until is displayed and press the 'OK/mode' button.
c) Press button to select the day you wish to copy and press the 'OK/mode' button.
d) The display will now show , , etc depending on which day you selected. The first number is
the day you are copying from, the second number is the day you are copying too.
e) By Pressing button you can now change the day you want to copy too, once happy Press the 'OK/mode'
button to copy.
f) You are now taken back to menu where you can Press the 'OK/mode' button to copy
another day (repeat from step c) ) or exit by Pressing the ' /esc' button.
Note:- If (Automatic Mode) is selected the heater cannot be turned off. To turn off the device, Press the
'OK/mode' button and use and buttons to select (Manual Mode) then Press the 'OK/mode' button.
You can now turn off the device using the ' /esc' button.
3.6 PILOT WIRING MODE
In this mode the device works following instructions from an external controller.
How to select FP mode?
a) Press the 'OK/mode' button.
b) Press the button until is displayed and press the 'OK/mode' button.
c) The display will show the set temperature together with a red flashing dot that indicates the unit is working
in FP mode.
Note:- If F.P. mode is selected the heater cannot be turned off. To turn off the device, press 'OK' and using the
and buttons select (Manual Mode) then Press the 'OK/mode' button. You can now turn off the
device using the ' /esc' button.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Climastar Silicium Touch at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Climastar Silicium Touch in the language / languages: English as an attachment in your email.

The manual is 1.59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info