599093
12
Zoom out
Zoom in
Previous page
1/134
Next page
12
TECHNISCHE DATEN DG 4,5 KW
Mindestfließdruck: 2 bar
Betriebsdruck: max. 10 bar
Empfohlener Betriebsdruck: 2 – 5 bar
Prüfdruck: 16 bar
Heißwassertemperatur: max. 70 °C
Empfohlene Heißwassertemp.: 60 °C
Durchflussleistung bei 3 bar:
Dampferzeuger:
9,1 l/min (Dampfbetrieb)
Dampferzeuger:
13 l/min (Dampfbetrieb + Drainage)
Ab 14 °d (2,5 mmol/l) Ihres Wassers ist
zum Schutz des Dampfgenerators eine
Wasserenthärtungsanlage in die Wasser-
zufuhr einzubauen.
Das Dampfmodul ist geeignet um einen
geschlossenen Raum von ca. 4 m3 aus-
reichend zu bedampfen!
Die Module bestehen aus folgenden
Werkstoffen:
- Eckschrank mit Dampftechnik aus
Acryl
Legende
A
Leerrohr 1 mit Innen-Ø 25 mm für
Stromversorgung:
Das mitgelieferte Stromversorgungskabel
mit Anschlussdose und Kupplungsstecker
für den Anschluß am Dampfgenerator
ermöglicht die Installation der Strom-
versorgung bis zu maximal ca. 6 m
entfernt vom Eckschrankmodul. Die
Anschlussdose muss jederzeit zugänglich
und im Trockenbereich (Schutzzone 3)
installiert werden.
Anschlussdose mit Elektroanschluss
400V/L1/L2/N/PE/50Hz für das Strom-
versorgungskabel vorsehen.
Die Absicherung muss über eine Feh-
lerstrom-Schutzeinrichtung (RCD) mit
einem Bemessungsdifferenz-strom ≤
30 mA. erfolgen.
B Leerrohr 2 mit Innen-Ø 25 mm für Tra-
fokabel:
Der mitgelieferte Trafo (Abmessung:
120x80x80mm) muss im Trockenbereich
(Schutzzone 3) installiert werden. Das
Trafokabel ermöglicht die Installation
des Trafos bis zu max. ca. 6 m entfernt
vom Eckschrankmodul. Der Trafo muss
jederzeit zugänglich sein. Ein beschä-
digter Anschluss kann nicht ersetzt
werden. Der Trafo darf dann nicht mehr
betrieben werden.
Der Trafo wird an eine Steckdose
230V/50Hz angeschlossen und muss über
eine Fehlerstrom-Schutzeinrichtung (RCD)
mit einem Bemessungsdifferenzstrom
von ≤ 30 mA abgesichert werden.
C Leerrohr 3 mit Innen-Ø 25 mm für Steu-
erleitung (12V~/40W) zum ansteuern
einer externen Beleuchtung (Beleuchtung
nicht im Lieferumfang)
Das mitgelieferte Verlängerungskabel
ermöglicht den Anschluss bis zu max.
ca. 4 m entfernt vom Modul..
TECHNICAL DATA DG 4,5 KW
Minimum flow pressure: 2 bar
Operating pressure: max. 10 bar
Recommended operating pressure:
2 – 5 bar
Test pressure: 16 bar
Hot water temperature: max. 70° C
Recommended hot water temp.: 60° C
Flow capacity at 3 bar
Steam generator:
9,7 l/h (steam operation)
Steam generator:
13 l/h (steam operation+ drain)
Install water softening equipment in the
water inlet to protect the steam gene-
rator as from water hardness level 14°d
(2,5 mmol/l) (German Standard).
The steam module is suitably to steam a
closed room of approx. 4 m3!
The modules consist of the following
materials:
- corner cabinet with steam system
made of acrylic material
Legend
A Wiring conduit 1 with internal diameter
of 25 mm for power supply:
The Steam generator is supplied with
a cable lead allowing for the mains
connection to be made approx 6m from
the corner of the cabin.
The connection must be accessible at
all times and must be installed in the
dry area (protection zone 3).
Plan socket with power supply connection
400V/L1/L2/N/PE/50Hz
The connection must be fused via a
2-pole RCCB with a residual current of
≤ 30 mA.
B
Wiring conduit 2 with internal diameter
of 25 mm for transformer cable:
The transformer (dimension:
120x80x80mm) must be installed in
the dry area (protection zone 3). The
transformer cable allows the connection
to be installed max. approx. 6 m from
corner cabinet. The transformer must
be accessible at all times. A damaged
connection cable cannot be replaced,
and the transformer must not be ope-
rated in this case.
The transformer must be connected
to a power outlet (230V/50Hz). The
connection must be fused via a 2-pole
RCCB with a residual current of ≤ 30
mA.
C Wiring conduit 3 with internal diameter
of 25 mm for control cable (12V~/40W)
for external lighting (the lighting isn't a
component of the delivery):
The enclosed extension cord allows
the connection max. approx. 4 m from
corner cabinet.
D TWW = hot water DN15 ½“
E Plan waterdrainage (Ø 50 mm) under
steam nozzle of the corner cabinet.
DATI TECNICI DG 4,5 KW
Pressione minima: 2 bar
Pressione di servizio: max. 10 bar
Pressione di servizio consigliata: 2 5 bar
Pressione di prova: 16 bar
Temperatura acqua calda: max. 70° C
Temp. acqua calda consigliata: 60° C
Portata con 3 bar
Generatore di vapore:
9,7 l/h (esercizio con vapore)
Generatore di vapore:
13 l/h (esercizio con vapore + drenaggio)
A partire da 14°d (2,5 mmol/l) dell'acqua,
a protezione del generatore di vapore è
indispensabile montare un impianto
per la addolcificazione dell'acqua
nell'alimentazione dell'acqua.
Il modulo vapore è adatto per produrre
vapore sufficiente per un locale chiuso
di ca. 4 m3!
I moduli sono costruiti con i seguenti
materiali:
- parete angolare con tecnologia del
vapore in materiale acrilico
Legenda
A Tubo vuoto di posa 1 con Ø interno 25
mm per l‘alimentazione elettrica:
Il cavo d’alimentazione di corrente elett-
rica in dotazione con spina di connettore
per l’allacciamento di rete al generatore
di vapore permette l’installazione
dell’alimentazione elettrica fino ad una
distanza massima di ca. 6m dal modulo
armadietto angolare. L’installazione del
collegamento deve essere eseguita in
modo da essere accessibile in qualsiasi
momento ed in zona asciutta (zona di
protezione 3).
Prevedere una scatola di collegamento
con il collegamento elettrico 400V/L1/
L2/N/PE/50Hz per il cavo d’alimentazione
di corrente elettrica.
La protezione deve essere eseguita
attraverso un interruttore automatico a
corrente residua (RCD) con una taratura
della corrente differenziale pari a ≤ 30
mA.
B Tubo vuoto di posa 2 con Ø interno 25
mm per cavo del trasformatore:
Il trasformatore in dotazione (Dimensione:
120x80x80mm) deve essere installato
in zona asciutta (zona di protezione 3).
Il cavo del trasformatore consente di
installare il trasformatore fino ad una
distanza massima di ca. 6m dal modulo
armadietto angolare. Il trasformatore
deve essere accessibile in qualsiasi
momento. Non è possibile sostituire
un collegamento danneggiato. In tal
caso non è più permesso utilizzare il
trasformatore.
Il trasformatore viene collegato ad una
presa di alimentazione 230V/50Hz e deve
essere protetto attraverso un interruttore
automatico a corrente residua (RCD) con
una taratura della corrente differenziale
pari a ≤ 30 mA.
C
Tubo vuoto di posa 3 con Ø interno 25 mm
12


Need help? Post your question in this forum.

Forumrules
1

Forum

cleopatra-pharo-dl-40

Reset search

  • Mon générateur affiche A18 après avoir demonter l'appareil j'ai découvert que la sonde a niveau a complètement fondue
    Qu'elle peut-être la cause et comment reparer est-ce qu'il faut acheter une autre sonde

    Merci Submitted on 18-6-2021 at 19:11

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cleopatra Pharo DL 40 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cleopatra Pharo DL 40 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 8,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info