Manual Clatronic es 2657 (page 34 of 59) (English, German, Dutch, French, Italian, Polish)

361372

Zoom out

Zoom in

1/59

Making a Espresso

1. Connect the machine to a correctly installed 230 V, 50 Hertz safety socket.

2. Ensure that the on/off switch (O/I) (6) is in the O position.

3. Place the draining grid in the indentation of the draining tray.

4. Open the lid and remove the water tank by the handle.

5. Fill the required amount of fresh clear water into the tank.

6. Release the filter holder (10) by turning the handle to the left (INSERT).

7. Place the filter (12 or 13) into the filter holder (10). Now add one to two level

measuring spoons of coffee. Distribute the coffee evenly and press the coffee

powder lightly with a measuring spoon or other spoon. The aim of pressing the

coffee powder with the spoon is to distribute it evenly in the coffee bowl rather

than compressing it. We recommend a flat surface plunger. Ensure that the fil-

ter holder is firmly fixed in the percolating head.

8. In order to preheat your espresso cups, place them on the warming plate (2)

above the percolating head.

9. Switch the machine on using the on/off switch (O/I) (6). The control lamps (4+

5) located on the right and left in the function control light up.

10. When the water has reached the required temperature, the control lamp (5) on

the right-hand side (READY) switches off. Note: if the control lamp lights up

again before percolation is finished, the water temperature is no longer high

enough. Turn the function selection switch (3) to O and wait for the lamp to go

out again. You can now continue preparing the espresso.

11. Remove the espresso cup(s) from the warming plate (2) and place them under

the percolating head.

12. Turn the function switch (3) to the symbol showing the espresso cup.

13. The espresso is now ready and is poured into the cup(s).

14. When percolation is finished, turn the function switch (3) back to the O position.

15. Switch the machine off using the on/off switch (O/I) (6).

16. After brewing wait for a few seconds before removing the filter. Turn the handle

of the filter holder from right to left. Pay attention to the steam! To remove the

used coffee, hold the filter by using the special lever (11) on the handle in the

relevant position. Turn the filter holder (10) and knock out the used coffee.

Remove the filter holder (10) after making an espresso. By doing so, you will

extend the service life of the rubber seal in the brewing head. To make other

espressos, fill the coffee bowl (12 or 13) with coffee powder again and carry out

the brewing procedure as described above.

Making a Cappuccino

To make a cappuccino, you must first make an espresso. Proceed as described

under “Making an Espresso” from steps 1 to 13. To froth the milk, proceed as follows:

1. Make sure that the function selector (3) is in O position.

2. Swing the steam nozzle (8) out so that you can position the container (please

use a heat-resistant container) comfortably under the nozzle.

44681-05-ES 2657 22.05.2003 16:52 Uhr Seite 34

How do I get Guan Screen for this machine, where I live in Egypt, thanks Submitted on 11-9-2020 at 17:01
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Clatronic es 2657 in the language / languages: English, German, Dutch, French, Italian, Polish as an attachment in your email.

The manual is 0,81 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Clatronic es 2657 Manual

Product: