580801
6
Zoom out
Zoom in
Previous page
1/13
Next page
6 XC6610
English
Owner’s Manual
INSTALLATION
This section suggests Mounting and Wiring Precautions for installing the Clarion
XC6610. If you do not posses the necessary tools and installation experience, do not
attempt to install these amplifiers. Instead, contact your local Clarion Audio dealer to
perform the installation.
MOUNTING PRECAUTIONS
Prior to mounting the amplifier, make sure it is safe to mount the amplifier in desired
location. Failure to do so can result in serious damage to the vehicle/ boat. Extra
care and attention is necessary in marine installations due to the uncertainty of
water conditions environment. Stainless steel hardware is recommended for marine
applications.
Additional precautions and suggestions:
1. For the most efficient cooling, mount the amplifier so cool air runs along the
length of the heat sink, rather than across them. To increase air movement and
circulation, a cooling fan can be installed.
2. Mount the amplifier on a rigid surface; avoid mounting to subwoofer enclosures or
areas prone to vibration.
3. Prior to drilling and mounting, make sure the proposed mounting holes will not cut
into the fuel tank, fuel lines, brake lines, electrical wiring, or the body of vehicle or
boat.
4. Do not mount the amplifier where it is susceptible to water.
WIRING PRECAUTIONS
Read all of the wiring precautions prior to making any connections. If you are unsure
and/or don’t have the necessary installation hardware, contact your local Clarion
audio dealer to perform the installation.
1. Before you begin the installation, make sure the vehicle is not running and is in
the OFF position.
2. Disconnect the negative (-) lead of the battery (or batteries) before making any
power connections.
3. When making connections, be sure that each connection is clean and secure.
Insulate final connections with electrical tape or heat shrink tubing. Failure to do
so may damage your equipment.
4. A good ground is critical for the performance of the amplifier. A ground wire
should be run directly from the battery to the amplifier (marine application). Use
black insulated 10-gauge or larger wire for the amplifier’s ground (-) power lead.
5. Add a fuse holder and fuse at the positive (+) terminal of the battery.
The fuse rating should equal the total current consumption at full output of the
amplifier(s). Use red insulated 10-gauge or larger wire for the amplifier’s positive
(+) power lead. Do not install the fuse until the complete installation has been
performed.
6. When replacing the amplifier’s fuse, always use one having the same amperage
rating. Substituting a higher rated fuse or a slow-blow type can result in serious
damage to the amplifier.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Clarion XC6610 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Clarion XC6610 in the language / languages: English as an attachment in your email.

The manual is 1,01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info