659137

Clarion EE-2178E Manual

2
Zoom out
Zoom in
Previous page
1/10
Next page
HOW TO INSTALL
How to attach the receiver
Precautions for attachment
•
Be sure to use the specified screws when attaching the
Precautions for attachment
1
Please install the receiver at stable position according to the
following diagram.
!
Antenna
Rotate the threaded portion of the antenna clockwise and fix
the antenna securely to the receiver to prevent loosening.
5
Mounting brackets
(Tow places)
7
Self tapping screws
(
5 mm x 16 mm)
(Four places)
6
Hexagon head bolts
with built-in washer
(M5 mm x 8 mm)
(Four places)
117 mm
45 mm
How to mount the camera with transmitter
CAUTION
Never swing the camera by the cable or pull the cable. Doing
so may impair the camera's watertightness or break the cable,
resulting in malfunction.
Avoid mounting the camera where the lens will be exposed to
dirt (mud splashes, exhaust fumes, etc.).
To prevent the camera from shaking, make sure the camera is
mounted to solid surface. The surface may need reinforcement if
it is not solid and secure.
Be sure to use the supplied screws to mount the camera. If
any screws are lost when mounting the camera, be sure to use
hexagon head bolts with built-in washer (M3 mm x 8 mm). Do
not under any circumstances use screws longer than this. To
ensure watertightness, the screw mounting holes in the camera
case have a bag structure. Use of long screws may damage the
screw thread and camera case, compromising watertightness.
1
Make a hole (2 places) for mounting the bracket in the
chassis and fix the bracket securely with the
$
hexagon
head bolts with built-in washer and flanged nuts.
2
Push-fit the gasket boss (2 places) into the guide hole from
inside the bracket.
3
Temporarily fix the camera in 4 places (a) with the
#
hexagon head bolts with built-in washer.
4
Using tools such as needle nose pliers, rotate the threaded
portion of the antenna clockwise and fix the antenna
securely to the camera to prevent loosening.
5
Temporarily fix the antenna bracket in 1 place (b) with the
#
hexagon head bolt with built-in washer so that the angle
of the antenna is controlled.
6
Install the wiring. (Refer to WIRING AND CONNECTIONS)
7
Adjust the mounting angle of the camera so that the rear
bumper or back end of the vehicle appears in the monitor
and tighten the bolts (a) to fix securely. (See diagram below)
Rear bumper or rear end of the vehicle
Monitor screen
The recommended guideline is approximately
1/10 of the monitor's overall height.
8
Adjust the antenna angle for optimal signal reception and
tighten the bolt (b) to fix securely.
PAIRING
When using the camera for the first time, pairing of the camera and the receiver is required. The pairing shall be done according to
the procedures below.
If the connected camera is replaced after pairing, the pairing procedure in Step 2 changes. The procedure is shown in the Advice
column.
Pairing Switch Operation
•Short-press the pairing switch
The cursor will move on the screen.
•Press and hold the pairing switch button for at least 3 seconds
Enter, or the pairing will start
The camera you want to
pair appears on the pairing
selection screen
The camera you want to
pair does not appear on
the pairing selection screen
The pairing selection
screen is not displayed.
(No compatible camera
was found)
Advice
•
You cannot pair an already paired camera with another receiver.
•
Once paired, the pairing information is saved when the power is
turned off.
•
If repeated searching fails to find the device you want to pair, it may
be due to poor radio wave reception. Replace the antenna on the
receiver with the optional long antenna and try again.
•
If the connected camera is replaced after pairing, Step 2 changes to
the following procedure.
1
Turn on the replacement camera and connect the antenna.
2
Press the pairing switch while the camera image is displayed.
The [Pairing changeover] screen appears.
3
Press and hold the pairing switch for at least 3 seconds while the
[Pairing changeover] screen is displayed.
The pairing selection screen appears.
Advice
Repeat Search
Check that the camera is turned on and
the antenna is connected. Point the cursor
to [ Search again ] and press the pairing
switch for at least 3 seconds.
Searching starts again.
1
Turn on the power.
The [Clarion] welcoming
screen appears and then
the screen changes in
sequence.
2
When the [Connecting]
screen appears, press and
hold the pairing switch for at
least 3 seconds.
The [Searching for the
pairing device] screen
appears.
The receiver is searching
for a camera to pair. When
the search is completed,
the pairing selection
screen appears.
3
Short-press the pairing
switch to point the cursor
to the camera number you
want to pair and press the
pairing switch for at least 3
seconds.
The selected camera
is connected and the
camera screen appears.
Advice
•
If the camera you want to pair does not appear
on the pairing selection screen or if the pairing
selection screen is not displayed, follow the steps
on the right to repeat the search.
•
If multiple camera numbers appear and you do
not know which to choose, select each number
in turn to find the right one.
Advice
4
If there is no problem with
the displayed camera
image, short-press the
pairing switch to point the
cursor to [Connect] and
press the pairing switch for
at least 3 seconds.
[Connect] disappears
from the screen and
only the camera image
is displayed. Pairing is
completed.
Advice
•
If a different screen is displayed, short-press the pairing
switch to point the cursor to [Cancel] and press the pairing
switch for at least 3 seconds.
Searching starts again and the search screen appears.
Advice
WIRING AND CONNECTIONS
•
When the power cable (red) of the camera/transmitter is connected to the ACC line, connect the
orange/white cable from the receiver to the ACC line along with the ACC signal (red).
•
If there is no ACC power for the transmitter, connect the camera/transmitter's red cable to the
parking light line. At the same time, be sure to connect the orange/white cable from the receiver to
the parking light line. In this case, the camera image is displayed only when the driver turns on the
illumination.
•
To prevent short-circuiting, check the connections again before connecting the battery.
RedBrown Black
Red
Orange
with white stripe
Purple
with white stripe
Black
ACC+
Connect to a positive power supply that can be turned on and
off with the ignition key.
Camera connection confirmation cable
Connect to a positive power supply where the camera red wire
is connected.
Reverse+
Connect to the reverse line which will have +12V/24V while in
reverse gear.
NOTE: Please connect to ACC line in order for the camera
image will be ready to display all the time.
Ground (Negative)
Connect to chassis ground.
ACC+ / Parking light+
Connect to the positive power supply that can be turned on and off
with the ignition key, or to the parking light line+.
NOTE: When you connect the red cable to the Parking light lne,
the parking lights would need to be on in order for the camera to
work and the camera image will be ready to display all the time.
Ground (Negative)
Connect to chassis groud.
This wire is not used.
●
Do not connect the power cable (red)
of either the transmitter or the receiver
to the +B line (permanent power
supply) as this may lead to a flat battery.
●
Disconnect the negative terminal of the
battery before connecting the cables.
Failure to do so may lead to electric
shock or injury due to short-circuit. It
may also lead
to damage to
the system
components
due to
short-circuit.
CAUTION
External monitor
(sold separately)
Example of monitor
combination
Pairing
switch
Camera
with transmitter
(CC-3500)
Receiver
(EE-2178)
TROUBLESHOOTING
The following situations may not be malfunctions, please check prior to requesting service.
Symptom Cause Measure
There is no image (Nothing appears
on the monitor)
The receiver is not connected
correctly
Check the receiver’s connections and connect the receiver
correctly
There is no image (“Connecting…” is
continuously displayed on the monitor)
The camera is not connected correctly Check the camera’s connections and connect the camera
correctly
The surrounding radio wave signal
strength is weak
Move to a different place and check if the image appears
The radio wave reception of the
camera is poor
Change the position of the antenna on the receiver or replace with the
optional long antenna and check again.
There is no paired camera around Press the pairing switch for at least 3 seconds to complete pairing.
The image cuts out (“The video has
been stopped” appears)
The surrounding radio wave signal
strength is weak
Move to a different place and check if the image appears
The radio wave reception of the
camera is poor
Change the position of the antenna on the receiver or replace with the
optional long antenna and check again.
“Communication has been
disconnected.” appears on the
monitor
The camera has been disconnected Depending on the state of the surrounding radio waves, the
camera is disconnected. Reconnection is automatic.
The camera you want to pair does not
appear on the pairing selection screen
The camera is not connected correctly Check the camera’s connections and connect the camera
correctly
The surrounding radio wave signal
strength is weak
Move to a different place and check if the image appears
The radio wave reception of the
camera is poor
Change the position of the antenna on the receiver or replace with the
optional long antenna and check again.
The camera you want to pair has been
paired with another receiver.
Turn off the receiver to which the camera you want to pair is
connected and wait a while (30 seconds) before pairing again.
“The button has been pressed for
more than 10 seconds.” appears
The pairing switch has been pressed
for more than 10 seconds
Check that there is nothing on top of the pairing switch pressing it
down, and then press the pairing switch once to return to the original
screen.
The pairing switch does not respond
when pressed
The pairing switch is not connected
correctly
Check the pairing switch’s connections and connect the button
correctly.
(a)
(a)
(a)
(b)
(a)
45 mm
¥
Antenna bracket
0
Mounting bracket
%
Flanged nuts (M5 mm) (Two places)
Vehicle side : 5.5 mm holes (Two places)
Boss
Boss
!
Antenna
@
Gaskets (Two places)
Threaded portion
of the antenna
#
Hexagon head
bolts with built-in
washer (a)
(M3 mm x 8 mm)
(Four places)
#
Hexagon head
bolt with built-in
washer (b)
(M3 mm x 8 mm)
(One place)
$
Hexagon head bolts with
built-in washer (M5 mm x
8 mm) (Two places)
Guide holes
Wiring Precaution
•
Please carry out waterproof treatment on hookup point
between camera power cable and vehicle wiring as per
the illustration below.
Camera power cable
Waterproof
Waterproof
Vehicle wiring
The end of
camera power cable
Wire connections
As well as wire connections, please do waterproof to
the end of camera power cable.
Wiring Precaution
2 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Clarion EE-2178E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Clarion EE-2178E in the language / languages: English, German, French, Swedish, Spanish as an attachment in your email.

The manual is 7,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info