455888
6
Zoom out
Zoom in
Previous page
1/12
Next page
19. SCRATCH BUTTON This button is used to activate the scratch effect by touching the
surface of the JOG WHEEL
20. ECHO BUTTON This button is used to add an ECHO effect to your output signal.
21. FLANGER BUTTON The FLANGER effect distorts the output signal and creates an
effect similar to the frequency, phasing in and out of each other.
22. FILTER BUTTON – The FILTER effect tweaks the original sound to add different tonal
definition.
23. BRAKE BUTTON – This button is used to adjust the START/STOP speed. When BRAKE is
activated you can press the X BUTTON and use the JOG WHEEL to adjust the start speed
of playback. If you press the Y BUTTON and use the JOG WHEEL you can adjust the stop
speed. This effect is then active when you press the PLAY / PAUSE BUTTON.
24. X PARAMETER BUTTON - (Time parameter) You can set the X parameter by rotating
the JOG WHEEL clockwise to increase the length of the effect or anticlockwise to
decrease the length of the effect.
25. Y PARAMETER BUTTON - (Ratio parameter) You can set the Y parameter by rotating
the JOG WHEEL clockwise to increase the level of the effect or anticlockwise to decrease
the level of the effect.
Note: When you stop using the JOG WHEEL to control the X & Y parameter effects.
The Parameter setting will return to the pre-set value.
26. HOLD BUTTON - Activating the HOLD button in combination with one of the above X or
Y buttons allows you to lock the level of either parameter. When the desired level is set,
deactivate the hold button for continued normal use.
27. CUE PLAY BUTTON – Pressing the CUE PLAY button will return the track to the previous
set cue point and continue playing.
28. MEMORY BUTTON - This “M” button can be used in a number of ways:
a. Press this button to activate memory mode (LED will glow) press your desired
memory bank (1-4) button to store your CUE points.
b. To store your cue points that are saved in the BANKS to the system memory for
next time, press and hold the “M” button for 2 seconds until it flashes
c. RECALL MEMORY: The MPCD-X1 can store 2048 cue points. That’s 4 cue points for
every 512 CDs. These settings may be easily recalled. Press EJECT so the draw is
open. Load your CD into the draw. Press the “M” button so it is illuminated. Then
close the CD draw. The unit will then display RECALL as the cue points are found in
the system memory (Note: this may take around 20 seconds).
29. TIME BUTTON - The button will switch the time value described in the TIME METER
between ELAPSED playing time, TRACK remaining time and TOTAL remaining time.
30. SGL/CTN BUTTON - This function allows you to choose between single track play or
continuous track play (all tracks in order with no pause between). This function also
operates in RELAY mode. With this button you can switch auto cue on and off, by holding
the button down for 2 seconds.
31. JOG WHEEL – The JOG WHEEL controls a number of different functions:
a. The JOG WHEEL will act as a frame search control when the track is in the pause or
cue mode, allowing you to set a point. If SCRATCH mode is activated then only the
outer part of the JOG WHEEL will act as a frame search.
b. The JOG WHEEL also works as a pitch bend during playback. Turning the wheel
clockwise will increase the pitch percentage up to 100%, and turning the wheel
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Citronic MPCD-X1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Citronic MPCD-X1 in the language / languages: English as an attachment in your email.

The manual is 1,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info