455907
3
Zoom out
Zoom in
Previous page
1/5
Next page
Rear Panel
Connection
Before connecting to amplifier or other equipment, turn down all volume controls to avoid loud noises which may
cause damage to other equipment. Always switch amplifier power on last in line with volume levels down.
Using good quality 6.3mm jack leads (balanced or unbalanced), connect L + R outputs from the mixer to the
amplifier, recorder or whichever equipment is to receive the main mix output.
If phantom power is to be used, press the +48V switch in.
Connect microphones, DI boxes and other balanced low impedance audio inputs to the mono channels using a
quality XLR lead.
Connect high impedance and line level signals to the mono inputs using a 6.3mm jack lead.
For the stereo channel, connect left and right line level signals via 6.3mm jack or RCA leads (unbalanced).
Channel inserts may be connected to individual processing equipment like EQ or compressors. These connections
completely interrupt the signal flow and divert to the external processor before returning to the channel for volume
adjustment via the channel fader. This requires a stereo to 2 x mono jack lead the 2 mono ends are send and
return connections, the stereo connection is wired as per below.
Recording equipment can be connected via the REC outputs using a twin RCA lead and the 6.3mm jack AUX
output can be connected to monitoring or external processing equipment if required. Individual levels can be
adjusted to the AUX output via the individual channel AUX controls.
For CM-LIVE models, if the internal delay effect is not required, a send can be connected from the EFFECT jack
output to and external effect unit, whereby the EFF channel controls act as individual level controls to the EFFECT
output (same as for AUX output)
With all faders down, connect the supplied AC adapter to the 12Vac input and to the mains supply (ensure correct
supply voltage) the power LED will illuminate (if phantom power is selected, this LED should light also)
Checking
Test each channels gain level by making the loudest expected sound into it and increasing the GAIN control until
the red PEAK LED starts to light. Then back the GAIN off slightly until the PEAK LED hardly lights at all.
Test the main mix output by increasing the MAIN fader and selected channel faders whilst making sound through
the channel(s) the L + R output LED ladders should begin to show the output as it varies up and down.
Connecting a pair of headphones to the PHONES stereo 6.3mm jack is a good way of checking the mix output,
remembering to gradually increase the PHONES level control.
Turn down all faders and then switch power on to connected equipment (amplifier last in line) and increase volume
levels. Gradually increase MAIN and channel faders again and the sound should be heard through the speakers or
be indicated on the recording equipment.
27. 12Vac power input (adapter supplied)
28. USB type B output/monitoring input (CM-STUDIO only)
29. L + R main output (on top control panel for CM-STUDIO)
30. SD card slot (CM-LIVE only)
31. USB type A input (CM-LIVE only)
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Citronic CM4-LIVE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Citronic CM4-LIVE in the language / languages: English as an attachment in your email.

The manual is 0,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info