650695
57
Zoom out
Zoom in
Previous page
1/136
Next page
Configuring the Voice Settings
Regional
Cisco SPA100 Series Administration Guide 65
1
Defining Ring and Cadence and Tone Scripts
To define ring and tone patterns, the ATA uses the concept of scripts. Below is information
about creating Cadence Scripts (CadScripts), Frequency Scripts (FreqScripts), and Tone
Scripts (ToneScripts).
CadScript
A mini-script of up to 127 characters that specifies the cadence parameters of a signal.
Syntax: S
1
[;S
2
], where:
S
i
=D
i
(on
i
,1/off
i
,1[,on
i
,
2
/off
i
,
2
[,on
i,3
/off
i
,
3
[,on
i
,
4
/off
i
,
4
[,on
i
,
5
/off
i
,
5
,on
i
,
6
/off
i,6
]]]]]) and is
known as a section, on
i,j
and off
i,j
are the on/off duration in seconds of a segment and i = 1 or
2, and j = 1 to 6. D
i
is the total duration of the section in seconds. All durations can have up to
three decimal places to provide 1 ms resolution. The wildcard character “*” represents infinite
duration. The segments within a section are played in order and repeated until the total
duration is played.
Example 1: 60(2/4)
Number of Cadence Sections = 1
Cadence Section 1: Section Length = 60 s
Number of Segments = 1
Segment 1: On=2s, Off=4s
Total Ring Length = 60s
Example 2—Distinctive ring (short,short,short,long): 60(.2/.2,.2/.2,.2/.2,1/4)
Number of Cadence Sections = 1
Cadence Section 1: Section Length = 60s
Number of Segments = 4
Segment 1: On=0.2s, Off=0.2s
Segment 2: On=0.2s, Off=0.2s
Segment 3: On=0.2s, Off=0.2s
Segment 4: On=1.0s, Off=4.0s
Total Ring Length = 60s
FreqScript
A mini-script of up to 127 characters that specifics the frequency and level parameters of a
tone.
Syntax: F
1
@L
1
[,F
2
@L
2
[,F
3
@L
3
[,F
4
@L
4
[,F
5
@L
5
[,F
6
@L
6
]]]]
Where F
1
F
6
are frequency in Hz (unsigned integers only) and L
1
L
6
are corresponding levels
in dBm (with up to 1 decimal places) White spaces before and after the comma are allowed
(but not recommended)
Example 1—Call Waiting Tone: 440@-10
Number of Frequencies = 1
Frequency 1 = 440 Hz at –10 dBm
57


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cisco Cisco SPA112 VoIP at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cisco Cisco SPA112 VoIP in the language / languages: English as an attachment in your email.

The manual is 1,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info