605005
20
Zoom out
Zoom in
Previous page
1/28
Next page
20
9 Perform Initial Configuration
This section provides the procedures for performing the initial configuration of your Cisco 815 integrated services router.
Configure the Router Using Cisco Router and Security Device Manager
Cisco Router and Security Device Manager (Cisco SDM) is a web-based configuration tool that allows you to configure LAN
and WAN interfaces, routing, Network Address Translation (NAT), firewalls, VPNs, and other features on your router. If Cisco
SDM is installed on your router, configure the router by following the instructions in the Cisco Router and Security Device
Manager Quick Start Guide. If this document was not shipped with your router, you can obtain Cisco SDM and instructions
for installing it on your router from the following location:
http://www.cisco.com/go/sdm
Note To obtain the Cisco SDM release notes, and other Cisco SDM documentation, go to http://www.cisco.com/go/sdm and
click the Technical Documentation link.
Setting Up the Initial Configuration Using the Setup Command Facility
This section shows how to use the setup command facility to configure a hostname for the Cisco 815 integrated services router,
to set passwords, and to configure an interface for communication with the management network. If the following messages
appear at the end of the startup sequence, the setup command facility has been invoked automatically:
--- System Configuration Dialog ---
At any point you may enter a question mark '?' for help.
Use ctrl-c to abort configuration dialog at any prompt.
Default settings are in square brackets '[]'.
Would you like to enter the initial configuration dialog? [yes/no]:
The setup command facility prompts you for basic information about your Cisco 815 integrated services router and network,
and it creates an initial configuration file. After the configuration file is created, you can use the CLI or Cisco Router and
Security Device Manager (Cisco SDM) to perform additional configuration.
The prompts in the setup command facility vary with the installed interface modules and the software image. The following
example and the user entries (in
bold) are shown as examples only.
For help with interface and port numbering, see the “Interface Numbering” section on page 17.
Note If you make a mistake while using the setup command facility, you can exit and run the setup command facility again.
Press Ctrl-C, and type setup at the privileged EXEC mode prompt (Router#).
Step 1 To proceed using the setup command facility, enter yes when the power-up messages have ended.
Would you like to enter the initial configuration dialog? [yes/no]: yes
Note If these messages do not appear, Cisco SDM and a default configuration file were installed on the router at the
factory. To use Cisco SDM to configure the router, see the “Configure the Router Using Cisco Router and
Security Device Manager” section on page 20.
Step 2 When the following messages appear, press Return to enter basic management setup:
At any point you may enter a question mark '?' for help.
Use ctrl-c to abort configuration dialog at any prompt.
Default settings are in square brackets '[]'.
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cisco 815 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cisco 815 in the language / languages: English as an attachment in your email.

The manual is 2,01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Cisco 815

Cisco 815 Installation Guide - English - 86 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info