65656
101
Zoom out
Zoom in
Previous page
1/122
Next page
Corporate Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 526-4100
Cisco IP Phone 7960G and 7940G
User Guide
Text Part Number: OL-4637-01
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT
NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT
ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR
THEIR APPLICATION OF ANY PRODUCTS.
THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION
PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO
LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.
The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference, in which case users will be required to correct the interference at their own expense.
The following information is for FCC compliance of Class B devices: The equipment described in this manual generates and may radiate
radio-frequency energy. If it is not installed in accordance with Cisco’s installation instructions, it may cause interference with radio and television
reception. This equipment has been tested and found to comply with the limits for a Class B digital device in accordance with the specifications in
part 15 of the FCC rules. These specifications are designed to provide reasonable protection against such interference in a residential installation.
However, there is no guarantee that interference will not occur in a particular installation.
Modifying the equipment without Cisco’s written authorization may result in the equipment no longer complying with FCC requirements for Class
A or Class B digital devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct
any interference to radio or television communications at your own expense.
You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco
equipment or one of its peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by
using one or more of the following measures:
• Turn the television or radio antenna until the interference stops.
• Move the equipment to one side or the other of the television or radio.
• Move the equipment farther away from the television or radio.
• Plug the equipment into an outlet that is on a different circuit from the television or radio. (That is, make certain the equipment and the television
or radio are on circuits controlled by different circuit breakers or fuses.)
Modifications to this product not authorized by Cisco Systems, Inc. could void the FCC approval and negate your authority to operate the product.
The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as
part of UCB’s public domain version of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California.
NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE
PROVIDED “AS IS” WITH ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED
OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.
IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL
DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR
INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES.
CCIP, CCSP, the Cisco Arrow logo, the Cisco Powered Network mark, Cisco Unity, Follow Me Browsing, FormShare, and StackWise are trademarks
of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn, and iQuick Study are service marks of Cisco Systems, Inc.; and Aironet,
ASIST, BPX, Catalyst, CCDA, CCDP, CCIE, CCNA, CCNP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, the Cisco IOS logo,
Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Empowering the Internet Generation, Enterprise/Solver, EtherChannel,
EtherSwitch, Fast Step, GigaStack, Internet Quotient, IOS, IP/TV, iQ Expertise, the iQ logo, iQ Net Readiness Scorecard, LightStream, MGX, MICA,
the Networkers logo, Networking Academy, Network Registrar, Packet, PIX, Post-Routing, Pre-Routing, RateMUX, Registrar, ScriptShare,
SlideCast, SMARTnet, StrataView Plus, Stratm, SwitchProbe, TeleRouter, The Fastest Way to Increase Your Internet Quotient, TransPath, and VCO
are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries.
All other trademarks mentioned in this document or Web site are the property of their respective owners. The use of the word partner does not imply
a partnership relationship between Cisco and any other company. (0304R)
Cisco IP Phone 7960G and 7940G User Guide
Copyright © 2000-2003, Cisco Systems, Inc.
All rights reserved.
v
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
CONTENTS
Preface xi
About this Guide xi
Related Documentation on the Web xiii
Obtaining Documentation xiii
Cisco.com xiii
Documentation CD-ROM xiv
Ordering Documentation xiv
Documentation Feedback xiv
Obtaining Technical Assistance xv
Cisco TAC Website xv
Opening a TAC Case xv
TAC Case Priority Definitions xvi
Obtaining Additional Publications and Information xvii
Document Conventions xviii
Statement 1071—Warning Definition xix
CHAPTER
1 Introducing Your Cisco IP Phone 1-1
Connecting Your Cisco IP Phone 1-2
Statement 1004—Installation Instructions 1-2
Identifying Buttons and Hardware 1-6
Auto-Registering Your Phone Using TAPS 1-10
Using Feature Buttons 1-10
Using Help on Your Phone 1-11
Using Softkeys 1-11
Contents
vi
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Choosing a Menu Item 1-12
Entering Characters on Your LCD Screen 1-12
Using the Handset, Speaker and Headset 1-12
Using the Handset 1-13
Adjusting the Handset Rest 1-13
Using the Speaker 1-14
Using a Headset 1-15
CHAPTER
2 Making Calls on Your Phone 2-1
Understanding Feature Availability 2-2
Placing, Answering, and Ending Calls 2-2
Placing a Call 2-2
Answering a Call 2-5
Ending a Call 2-6
Getting Notified When a Busy Line Is Available Using Cisco Call Back 2-6
Searching and Dialing from the Phone Directory 2-7
Viewing and Dialing from the Phone Logs 2-8
Using Mute and Hold 2-9
Tracing Suspicious Calls 2-10
Extending Speed Dial Functionality 2-10
Setting Up and Receiving Priority Calls 2-11
Setting Up a Priority Call 2-12
Receiving a Priority Call 2-12
MLPP Messages 2-13
CHAPTER
3 Redirecting Calls on Your Phone 3-1
Transferring Calls 3-1
Transferring a Call to Another Extension 3-1
vii
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Contents
Directly Transferring Your Calls 3-2
Scenarios for Directly Transferring Your Calls 3-2
Storing and Retrieving a Call Using Call Park 3-4
Answering Calls that are Ringing on Another Extension Using Call Pickup 3-5
How to Pick Up Calls Within Your Group 3-5
How to Pick Up Calls Outside of Your Group 3-6
Forwarding Calls to Another Extension 3-6
Setting Up Call Forwarding on Your Phone 3-7
Canceling Call Forwarding on Your Phone 3-8
Sending Calls to a Voice Messaging System 3-8
CHAPTER
4 Making Conference Calls on Your Phone 4-1
Placing a Conference Call 4-1
Viewing Participants in a Conference Call 4-2
Selecting Participants to Join a Conference Call 4-3
Adding Your Line to a Shared Line Call 4-4
Understanding Shared Lines 4-4
Support for Conference Modes 4-5
Keeping Your Call Information Private 4-7
Using Meet-me Conferences 4-8
Establishing a Meet-me Conference 4-8
Joining a Meet-me Conference 4-9
CHAPTER
5 Customizing Settings on Your Phone 5-1
Adjusting the Handset, Speakerphone, and Headset Volume 5-1
Adjusting the Ringer Volume 5-2
Personalizing the Ringer Sound 5-2
Changing the LCD Screen Contrast 5-4
Contents
viii
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
CHAPTER
6 Customizing Your Phone on the Web 6-1
Logging on to the User Options Web Pages 6-1
Changing your Password or PIN 6-2
Customizing Your Cisco IP Phone on the Web 6-3
CHAPTER
7 Using Your Voice Messaging System 7-1
CHAPTER
8 Managing Your Phone Contacts 8-1
Using a Personal Address Book 8-2
Searching Personal Address Book Entries on Your Phone 8-2
Editing a Personal Address Book Entry on Your Phone 8-3
Dialing a Personal Address Book Entry 8-3
Using the Cisco IP Phone Address Book Synchronizer 8-4
Using the Fast Dial Service 8-4
Creating a Fast Dial Entry for a Number in Your Personal Address Book on
Your Phone
8-4
Creating a Fast Dial Entry for a Non-Address Book Directory Number on Your
Phone
8-5
Removing a Fast Dial Entry on Your Phone 8-6
Dialing a Fast Dial Entry 8-6
CHAPTER
9 Logging In to Your Extension Using the Cisco CallManager Extension
Mobility Feature
9-1
Logging In to Cisco CallManager Extension Mobility 9-2
Logging Out of Cisco CallManager Extension Mobility 9-3
Changing Your Cisco CallManager Extension Mobility PIN 9-4
CHAPTER
10 Troubleshooting Your Phone 10-1
Tips for Cleaning Your Cisco IP Phone 10-1
ix
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Contents
Tips for General Troubleshooting on Your
Cisco IP Phone
10-1
Diagnosing Problems 10-3
Accessing Network Configuration Data 10-3
Accessing Model Information 10-4
Accessing Status Data 10-5
Troubleshooting Cisco CallManager Extension Mobility 10-5
Using the Quality Reporting Tool 10-7
APPENDIX
A FAQ A-1
How do I access my voice messages? A-2
How do I set up speed-dial numbers? A-2
How do I set up softkeys for speed dialing? A-2
How do I access the User Options web page? A-3
How do I see a list of my missed calls? A-3
How do I put a call on hold without a hold button? A-3
How do I change the contrast on the phone’s LCD screen? A-3
How do I change the settings for my Cisco CallManager Extension Mobility
line?
A-3
How do I forward calls? A-4
How do I directly transfer calls? A-4
How do I join multiple parties into one call? A-4
How can I see a list of participants in an ad hoc conference call? A-4
How do I add my line to a shared line call? A-5
How do I keep my call information private? A-5
How do I store frequently-called numbers? A-5
I’ve used up all my speed-dial buttons, can I add more? A-6
Contents
x
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
What is the maximum number of speed-dial numbers that I can configure on my
phone?
A-6
How do I assign a phone service to a button on my
Cisco IP Phone?
A-6
If I cannot answer a call that I have forwarded to another number, will the call get
rerouted to my voice messaging system?
A-7
How do I set priority levels for my calls? A-7
How can I send calls directly to a voice messaging system? A-7
Why don’t I get a dial tone after dialing an access code? A-8
How do I trace a suspicious call? A-8
Where can I find tips about cleaning my
Cisco IP Phone?
A-8
Where can I find general troubleshooting tips for my Cisco IP Phone? A-8
APPENDIX
B Safety Notices B-1
I
NDEX
xi
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Preface
This preface covers these topics:
About this Guide, page xi
Related Documentation on the Web, page xiii
Obtaining Documentation, page xiii
Obtaining Technical Assistance, page xv
Obtaining Additional Publications and Information, page xvii
Document Conventions, page xviii
About this Guide
Use this guide to perform basic and advanced phone tasks using your
Cisco IP Phone 7960G or 7940G with Cisco CallManager.
Note Some of the features described in this book might not be available on your phone.
For more information about the features supported on your phone, contact your
system administrator.
Preface
About this Guide
xii
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
This book is organized in the following way:
Chapter Contents
Chapter 1, “Introducing Your
Cisco IP Phone”
Instructions on installing your phone, as well as an overview
of your phone.
Chapter 2, “Making Calls on Your
Phone”
Information and procedures for placing, answering, and
ending calls.
Chapter 3, “Redirecting Calls on Your
Phone”
Information and procedures for transfering and forwading
calls, and other ways of redirecting your phone calls.
Chapter 4, “Making Conference Calls
on Your Phone”
Information and procedures for setting up conference calls.
Chapter 5, “Customizing Settings on
Your Phone”
Information and procedures for configuring volume, contrast,
and other phone settings.
Chapter 6, “Customizing Your Phone
on the Web”
Information and procedures for customizing your phone via
the User Options web pages.
Chapter 7, “Accessing Voice Messages
on Your Phone”
Information about setting up and using your voice messaging
system.
Chapter 8, “Managing Your Phone
Contacts”
Information and procedures for managing your contacts on
your phone and on the web using the Personal Directories,
Personal Address Book, Fast Dials, and more.
Chapter 9, “Logging In to Your
Extension Using the Cisco
CallManager Extension Mobility
Feature”
Information about using Cisco CallManager
Extension Mobility.
Chapter 10, “Troubleshooting Your
Phone”
General care and troubleshooting, error codes and their
meanings, and ways of getting status and configuration data
about your phone.
Appendix A, “FAQ” Contains Frequently Asked Questions (FAQ) about your
Cisco IP Phone.
Appendix B, “Safety Notices” Lists safety information about your phone.
xiii
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Preface
Related Documentation on the Web
Related Documentation on the Web
For more information, refer to these documents:
Cisco IP Phone 7960G and 7940G Phone Guide—This booklet includes basic
installation instructions and ships in the box with each phone.
Cisco IP Phone 7914 Expansion Module Phone Guide—This guide includes
user instructions and installation information for the Cisco IP Phone 7914
Expansion Module.
Regulatory Compliance and Safety Information for the Cisco IP Phone 7900
Series—This document provides international agency compliance, safety,
and statutory information for Cisco IP Phone 7900 series models.
Customizing Your Cisco IP Phone on the Web—This document provides
information about how to configure phone services and features from the
Cisco CallManager User Options web page.
These documents are available on the web at this URL:
http://www.cisco.com/univercd/cc/td/doc/product/voice/c_ipphon/index.htm
Obtaining Documentation
Cisco provides several ways to obtain documentation, technical assistance, and
other technical resources. These sections explain how to obtain technical
information from Cisco Systems.
Cisco.com
You can access the most current Cisco documentation on the World Wide Web at
this URL:
http://www.cisco.com/univercd/home/home.htm
You can access the Cisco website at this URL:
http://www.cisco.com
International Cisco websites can be accessed from this URL:
http://www.cisco.com/public/countries_languages.shtml
Preface
Obtaining Documentation
xiv
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Documentation CD-ROM
Cisco documentation and additional literature are available in a Cisco
Documentation CD-ROM package, which might have shipped with your product.
The Documentation CD-ROM is updated regularly and might be more current
than printed documentation. The CD-ROM package is available as a single unit or
through an annual or quarterly subscription.
Registered Cisco.com users can order a single Documentation CD-ROM (product
number DOC-CONDOCCD=) through the Cisco Ordering tool:
http://www.cisco.com/en/US/partner/ordering/ordering_place_order_ordering_t
ool_launch.html
All users can order annual or quarterly subscriptions through the online
Subscription Store:
http://www.cisco.com/go/subscription
Ordering Documentation
You can find instructions for ordering documentation at this URL:
http://www.cisco.com/univercd/cc/td/doc/es_inpck/pdi.htm
You can order Cisco documentation in these ways:
Registered Cisco.com users (Cisco direct customers) can order Cisco product
documentation from the Networking Products MarketPlace:
http://www.cisco.com/en/US/partner/ordering/index.shtml
Nonregistered Cisco.com users can order documentation through a local
account representative by calling Cisco Systems Corporate Headquarters
(California, USA.) at 408 526-7208 or, elsewhere in North America, by
calling 800 553-NETS (6387).
Documentation Feedback
You can submit comments electronically on Cisco.com. On the Cisco
Documentation home page, click Feedback at the top of the page.
You can send your comments in e-mail to bug-doc@cisco.com.
xv
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Preface
Obtaining Technical Assistance
You can submit comments by using the response card (if present) behind the front
cover of your document or by writing to the following address:
Cisco Systems
Attn: Customer Document Ordering
170 West Tasman Drive
San Jose, CA 95134-9883
We appreciate your comments.
Obtaining Technical Assistance
For all customers, partners, resellers, and distributors who hold valid Cisco
service contracts, the Cisco Technical Assistance Center (TAC) provides 24-hour,
award-winning technical support services, online and over the phone. Cisco.com
features the Cisco TAC website as an online starting point for technical assistance.
Cisco TAC Website
The Cisco TAC website (http://www.cisco.com/tac) provides online documents
and tools for troubleshooting and resolving technical issues with Cisco products
and technologies. The Cisco TAC website is available 24 hours a day, 365 days a
year.
Accessing all the tools on the Cisco TAC website requires a Cisco.com user ID
and password. If you have a valid service contract but do not have a login ID or
password, register at this URL:
http://tools.cisco.com/RPF/register/register.do
Opening a TAC Case
The online TAC Case Open Tool (http://www.cisco.com/tac/caseopen) is the
fastest way to open P3 and P4 cases. (Your network is minimally impaired or you
require product information). After you describe your situation, the TAC Case
Open Tool automatically recommends resources for an immediate solution. If
your issue is not resolved using these recommendations, your case will be
assigned to a Cisco TAC engineer.
Preface
Obtaining Technical Assistance
xvi
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
For P1 or P2 cases (your production network is down or severely degraded) or if
you do not have Internet access, contact Cisco TAC by telephone. Cisco TAC
engineers are assigned immediately to P1 and P2 cases to help keep your business
operations running smoothly.
To open a case by telephone, use one of the following numbers:
Asia-Pacific: +61 2 8446 7411 (Australia: 1 800 805 227)
EMEA: +32 2 704 55 55
USA: 1 800 553-2447
For a complete listing of Cisco TAC contacts, go to this URL:
http://www.cisco.com/warp/public/687/Directory/DirTAC.shtml
TAC Case Priority Definitions
To ensure that all cases are reported in a standard format, Cisco has established
case priority definitions.
Priority 1 (P1)—Your network is “down” or there is a critical impact to your
business operations. You and Cisco will commit all necessary resources around
the clock to resolve the situation.
Priority 2 (P2)—Operation of an existing network is severely degraded, or
significant aspects of your business operation are negatively affected by
inadequate performance of Cisco products. You and Cisco will commit full-time
resources during normal business hours to resolve the situation.
Priority 3 (P3)—Operational performance of your network is impaired, but most
business operations remain functional. You and Cisco will commit resources
during normal business hours to restore service to satisfactory levels.
Priority 4 (P4)—You require information or assistance with Cisco product
capabilities, installation, or configuration. There is little or no effect on your
business operations.
xvii
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Preface
Obtaining Additional Publications and Information
Obtaining Additional Publications and Information
Information about Cisco products, technologies, and network solutions is
available from various online and printed sources.
The Cisco Product Catalog describes the networking products offered by
Cisco Systems, as well as ordering and customer support services. Access the
Cisco Product Catalog at this URL:
http://www.cisco.com/en/US/products/products_catalog_links_launch.html
Cisco Press publishes a wide range of networking publications. Cisco
suggests these titles for new and experienced users: Internetworking Terms
and Acronyms Dictionary, Internetworking Technology Handbook,
Internetworking Troubleshooting Guide, and the Internetworking Design
Guide. For current Cisco Press titles and other information, go to Cisco Press
online at this URL:
http://www.ciscopress.com
Packet magazine is the Cisco quarterly publication that provides the latest
networking trends, technology breakthroughs, and Cisco products and
solutions to help industry professionals get the most from their networking
investment. Included are networking deployment and troubleshooting tips,
configuration examples, customer case studies, tutorials and training,
certification information, and links to numerous in-depth online resources.
You can access Packet magazine at this URL:
http://www.cisco.com/go/packet
iQ Magazine is the Cisco bimonthly publication that delivers the latest
information about Internet business strategies for executives. You can access
iQ Magazine at this URL:
http://www.cisco.com/go/iqmagazine
Internet Protocol Journal is a quarterly journal published by Cisco Systems
for engineering professionals involved in designing, developing, and
operating public and private internets and intranets. You can access the
Internet Protocol Journal at this URL:
http://www.cisco.com/en/US/about/ac123/ac147/about_cisco_the_internet_
protocol_journal.html
Training—Cisco offers world-class networking training. Current offerings in
network training are listed at this URL:
Preface
Document Conventions
xviii
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
http://www.cisco.com/en/US/learning/index.html
Document Conventions
This document uses the following conventions:
Note Means reader take note. Notes contain helpful suggestions or references to
material not covered in the publication.
Caution Means reader be careful. In this situation, you might do something that could
result in equipment damage or loss of data.
Convention Description
boldface font Commands and keywords are in boldface.
italic font Arguments for which you supply values are in
italics.
[ ] Elements in square brackets are optional.
string A nonquoted set of characters. Do not use quotation
marks around the string or the string will include the
quotation marks.
screen font Terminal sessions and information the system
displays are in
screen font.
boldface screen font Information you must enter is in boldface screen
font.
italic screen font Arguments for which you supply values are in italic
screen font.
xix
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Preface
Document Conventions
Warnings use the following conventions:
Statement 1071—Warning Definition
Warning
IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could cause
bodily injury. Before you work on any equipment, be aware of the hazards
involved with electrical circuitry and be familiar with standard practices for
preventing accidents. Use the statement number provided at the end of each
warning to locate its translation in the translated safety warnings that
accompanied this device.
SAVE THESE INSTRUCTIONS
Waarschuwing
BELANGRIJKE VEILIGHEIDSINSTRUCTIES
Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die
lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat
werken, dient u zich bewust te zijn van de bij elektrische schakelingen
betrokken risico's en dient u op de hoogte te zijn van de standaard praktijken
om ongelukken te voorkomen. Gebruik het nummer van de verklaring
onderaan de waarschuwing als u een vertaling van de waarschuwing die bij
het apparaat wordt geleverd, wilt raadplegen.
BEWAAR DEZE INSTRUCTIES
Varoitus
TÄRKEITÄ TURVALLISUUSOHJEITA
Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia
vammoja. Ennen kuin käsittelet laitteistoa, huomioi sähköpiirien
käsittelemiseen liittyvät riskit ja tutustu onnettomuuksien yleisiin
ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen
mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta
varoitusten lopussa näkyvien lausuntonumeroiden avulla.
SÄILYTÄ NÄMÄ OHJEET
Preface
Document Conventions
xx
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Attention
IMPORTANTES INFORMATIONS DE SÉCURITÉ
Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une
situation pouvant entraîner des blessures ou des dommages corporels. Avant
de travailler sur un équipement, soyez conscient des dangers liés aux circuits
électriques et familiarisez-vous avec les procédures couramment utilisées
pour éviter les accidents. Pour prendre connaissance des traductions des
avertissements figurant dans les consignes de sécurité traduites qui
accompagnent cet appareil, référez-vous au numéro de l'instruction situé à la
fin de chaque avertissement.
CONSERVEZ CES INFORMATIONS
Warnung
WICHTIGE SICHERHEITSHINWEISE
Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die
zu Verletzungen führen kann. Machen Sie sich vor der Arbeit mit Geräten mit
den Gefahren elektrischer Schaltungen und den üblichen Verfahren zur
Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder Warnung
angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den
übersetzten Sicherheitshinweisen, die zusammen mit diesem Gerät
ausgeliefert wurden.
BEWAHREN SIE DIESE HINWEISE GUT AUF.
Avvertenza
IMPORTANTI ISTRUZIONI SULLA SICUREZZA
Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe
causare infortuni alle persone. Prima di intervenire su qualsiasi
apparecchiatura, occorre essere al corrente dei pericoli relativi ai circuiti
elettrici e conoscere le procedure standard per la prevenzione di incidenti.
Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per
individuare le traduzioni delle avvertenze riportate in questo documento.
CONSERVARE QUESTE ISTRUZIONI
xxi
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Preface
Document Conventions
Advarsel
VIKTIGE SIKKERHETSINSTRUKSJONER
Dette advarselssymbolet betyr fare. Du er i en situasjon som kan føre til skade
på person. Før du begynner å arbeide med noe av utstyret, må du være
oppmerksom på farene forbundet med elektriske kretser, og kjenne til
standardprosedyrer for å forhindre ulykker. Bruk nummeret i slutten av hver
advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som
fulgte med denne enheten.
TA VARE PÅ DISSE INSTRUKSJONENE
Aviso
INSTRUÇÕES IMPORTANTES DE SEGURANÇA
Este símbolo de aviso significa perigo. Você está em uma situação que poderá
ser causadora de lesões corporais. Antes de iniciar a utilização de qualquer
equipamento, tenha conhecimento dos perigos envolvidos no manuseio de
circuitos elétricos e familiarize-se com as práticas habituais de prevenção de
acidentes. Utilize o número da instrução fornecido ao final de cada aviso para
localizar sua tradução nos avisos de segurança traduzidos que acompanham
este dispositivo.
GUARDE ESTAS INSTRUÇÕES
¡Advertencia!
INSTRUCCIONES IMPORTANTES DE SEGURIDAD
Este símbolo de aviso indica peligro. Existe riesgo para su integridad física.
Antes de manipular cualquier equipo, considere los riesgos de la corriente
eléctrica y familiarícese con los procedimientos estándar de prevención de
accidentes. Al final de cada advertencia encontrará el número que le ayudará
a encontrar el texto traducido en el apartado de traducciones que acompaña
a este dispositivo.
GUARDE ESTAS INSTRUCCIONES
Preface
Document Conventions
xxii
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Varning!
VIKTIGA SÄKERHETSANVISNINGAR
Denna varningssignal signalerar fara. Du befinner dig i en situation som kan
leda till personskada. Innan du utför arbete på någon utrustning måste du vara
medveten om farorna med elkretsar och känna till vanliga förfaranden för att
förebygga olyckor. Använd det nummer som finns i slutet av varje varning för
att hitta dess översättning i de översatta säkerhetsvarningar som medföljer
denna anordning.
SPARA DESSA ANVISNINGAR
xxiii
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Preface
Document Conventions
Preface
Document Conventions
xxiv
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
CHAPTER
1-1
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
1
Introducing Your Cisco IP Phone
A Cisco IP Phone is a full-featured telephone that provides voice communication
over the same data network that your computer uses. This phone functions much
like a traditional analog phone, allowing you to place and receive telephone calls.
It also supports features that you have come to expect from a telephone—such as
speed dialing, redial, call transfer, conference calling, and voice messaging
access.
Your Cisco IP Phone offers features that might surprise you. Because it is part of
an IP network, your Cisco IP Phone can provide not only telephony services, but
also data services—including up-to-the-minute information and services from the
network. With a Cisco IP Phone, you have access to a whole range of
communication features that are not available on a traditional telephone.
This guide helps you learn how to use the various features and services available
on your phone. Not all of the features described in this book are available by
default—your system administrator determines the services that are available to
you. You access some phone features and services on the phone itself, while you
customize others on a convenient web page. For information about the User
Options web page, see Chapter 6, “Customizing Your Phone on the Web.”
Note Your company’s phone support team determines which features and services are
available to you and how they will be configured. Some of the features included
in this User Guide might not be available to you or might work differently on your
phone system. Contact your support desk or system administrator if you have
questions about feature availability.
Chapter 1 Introducing Your Cisco IP Phone
Connecting Your Cisco IP Phone
1-2
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
This chapter covers the following topics:
Connecting Your Cisco IP Phone, page 1-2
Identifying Buttons and Hardware, page 1-6
Auto-Registering Your Phone Using TAPS, page 1-10
Using Feature Buttons, page 1-10
Using Help on Your Phone, page 1-11
Using Softkeys, page 1-11
Choosing a Menu Item, page 1-12
Entering Characters on Your LCD Screen, page 1-12
Using the Handset, Speaker and Headset, page 1-12
Using the Speaker, page 1-14
Using a Headset, page 1-15
Connecting Your Cisco IP Phone
Chances are, your system administrator or a technician will connect your new
Cisco IP Phone to the corporate IP telephony network. If that is not the case,
connecting your phone is easy.
Statement 1004—Installation Instructions
Warning
Read the installation instructions before connecting the system to the power
source.
Statement 1004
Waarschuwing
Raadpleeg de installatie-instructies voordat u het systeem op de voedingsbron
aansluit.
Varoitus
Lue asennusohjeet ennen järjestelmän yhdistämistä virtalähteeseen.
1-3
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Chapter 1 Introducing Your Cisco IP Phone
Connecting Your Cisco IP Phone
Attention
Avant de brancher le système sur la source d'alimentation, consulter les
directives d'installation.
Warnung
Vor dem Anschließen des Systems an die Stromquelle die
Installationsanweisungen lesen.
Avvertenza
Consultare le istruzioni di installazione prima di collegare il sistema
all'alimentatore.
Advarsel
Les installasjonsinstruksjonene før systemet kobles til strømkilden.
Aviso
Leia as instruções de instalação antes de ligar o sistema à fonte de energia.
¡Advertencia!
Lea las instrucciones de instalación antes de conectar el sistema a la red de
alimentación.
Varning!
Läs installationsanvisningarna innan du kopplar systemet till
strömförsörjningsenheten.
Chapter 1 Introducing Your Cisco IP Phone
Connecting Your Cisco IP Phone
1-4
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
See Figure 1-1 to locate connections on the back of your phone.
Figure 1-1 Cisco IP Phone Cable Connections
RS232
DC48V
10/100 SW 10/100 PC
+
58670
2
3
4
5
6
7
1
1-5
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Chapter 1 Introducing Your Cisco IP Phone
Connecting Your Cisco IP Phone
Before You Begin
Verify that your system administrator is ready for you to connect your
Cisco IP Phone to the network.
Warning
Be sure to read Appendix B, “Safety Notices,” before connecting or using your
phone.
Procedure
Step 1 Connect your Cisco IP Phone to the corporate IP telephony network. You can do
this in one of two ways, depending on how your workspace is set up. (See your
system administrator if you are not sure which method to choose.)
Direct network connection—For this method, you need at least one available
Ethernet port in your workspace. Use the Ethernet cable included with your
phone to connect the network port on the back of your phone to the Ethernet
port in your workspace.
Shared network connection—Use this method if you have a single Ethernet
port in your workspace with your desktop computer already connected to it.
First, disconnect the Ethernet cable from the computer and attach it to the
network port on the back of your phone. Next, use the Ethernet cable included
with your phone to connect the access port on the back of your phone to your
desktop computer. Your Cisco IP Phone now shares a network connection
with your computer.
1 AC/DC adapter port (DC48V) for power
connector (for phones not provided with
inline power)
5 Access port (10/100 PC)
for connecting your phone
to your PC
2 Power supply with DC connector for
phone
6 Handset port for
connecting the handset
3 AC power cable with wall socket plug 7 Headset port for
connecting a headset
4 Network port (10/100 SW) for
connecting to the network
Chapter 1 Introducing Your Cisco IP Phone
Identifying Buttons and Hardware
1-6
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Step 2 Connect the handset to the handset port. Ensure that the end of the cord with the
longer uncoiled section is connected to the body of the phone.
Step 3 If your system administrator delivered your Cisco IP Phone with a power supply,
connect the power supply plug to the DC48V AC adapter port on the back of the
phone.
If your system administrator delivered your phone without a power supply, your
phone probably receives power through the Ethernet connection.
Step 4 Use the power cable to connect the power supply to a standard power outlet in
your workspace.
Step 5 To adjust the footstand height, release the footstand by pressing the footstand
adjustment knob and gently pull the footstand away from the body of the phone.
See the Adjusting the Handset Rest” section on page 1-13 for information on
adjusting the handset rest to make sure the receiver will sit securely in the cradle.
Startup
Once you connect the Cisco IP Phone to its power source, a startup process
begins. After several minutes, the phone’s LCD screen displays a neutral “ready”
screen. The details on your screen might vary, but a ready screen typically
displays the date and time, your extension number, and the available softkeys.
Startup is complete and your phone is ready to use.
Tip Softkeys point to feature options displayed along the bottom of your LCD screen.
Softkeys are flexible—they change depending on the status of your phone. See the
“Using Softkeys” section on page 1-11 for additional information.
Identifying Buttons and Hardware
See the following illustrations and table to identify the buttons and hardware on
your Cisco IP Phone, and find descriptions of related features.
1-7
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Chapter 1 Introducing Your Cisco IP Phone
Identifying Buttons and Hardware
Figure 1-2 Cisco IP Phone 7960
Figure 1-3 Cisco IP Phone 7940
1
4
5
1617
15
68561
3
9
7
6
2
1011
121314
8
68562
1
4
10111617 12131415
5
9
7
8
2
6
3
Chapter 1 Introducing Your Cisco IP Phone
Identifying Buttons and Hardware
1-8
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
1 Handset with
indicator light
Functions like a traditional handset. The light strip at the
top of the handset blinks when the phone rings and can be
set to remain lit when you receive a voice message.
For more information on working with the handset, see the
“Using the Handset, Speaker and Headset” section on
page 1-12.
2 LCD screen Displays features such as the time, date, your phone
number, caller ID, line/call status and softkey tabs.
3 Cisco IP Phone
model type
Indicates your Cisco IP Phone model.
4 Line or speed
dial button
Opens a new line or speed dials the number on the LCD
screen. Phones in the Cisco IP Phone 7960 series have six
line or speed-dial buttons and phones in the 7940 series
have two. See the “Extending Speed Dial Functionality”
section on page 2-10 and the “Customizing Your Cisco IP
Phone on the Web” section on page 6-3.
5 Footstand
adjustment
Allows you to adjust the angle of the phone base.
6 Directories
button
Provides access to call histories and directories (see the
“Using Feature Buttons” section on page 1-10.)
7 ? button Displays help on your LCD screen for a phone button or
function (see the Using Help on Your Phone section on
page 1-11.)
8 Settings button Provides access to phone settings such as contrast and ring
sound, network configuration, and status information (see
the Using Feature Buttons section on page 1-10.)
9 Speaker button Toggles the speaker on or off. See the Using the Speaker
section on page 1-14.
10 Mute button Toggles the mute on or off. See the Using Mute and
Hold section on page 2-9.
1-9
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Chapter 1 Introducing Your Cisco IP Phone
Identifying Buttons and Hardware
11 Headset button Toggles the headset on or off.
For more information on working with the headset, see the
Using a Headset section on page 1-15.
12 Volume button Increases or decreases volume for the handset, headset, or
speakerphone (depending upon which is currently active).
Also controls the ringer volume (if the handset is in its
cradle), and the LCD screen contrast.
For more information on adjusting the volume, see the
Adjusting the Handset, Speakerphone, and Headset
Volume section on page 5-1 and the Adjusting the
Ringer Volume section on page 5-2.
13 Services button Provides access to any available phone services (see the
Using Feature Buttons section on page 1-10.)
14 Messages
button
Provides access to a message system, if available (see the
Using Feature Buttons section on page 1-10.)
15 Navigation
button
Enables you to scroll through text and select features
displayed on the LCD screen (see the Choosing a Menu
Item section on page 1-12.)
16 Keypad Works exactly like the keypad on a traditional telephone.
17 Softkeys Enable you to engage any of the functions displayed on the
corresponding LCD screen tabs. Softkeys point to feature
options displayed along the bottom of your LCD screen.
Softkeys change depending on the status of your phone.
For example, you can see one set of softkey options when
you pick up the handset, and another set when the phone
is not in use (see the Using Softkeys section on
page 1-11.)
Chapter 1 Introducing Your Cisco IP Phone
Auto-Registering Your Phone Using TAPS
1-10
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Auto-Registering Your Phone Using TAPS
After your phone is installed and connected to the network, your system
administrator might ask you to auto-register your phone using TAPS (Tool for
Auto-Registered Phones Support). TAPS might be used either for a new phone or
to replace an existing phone.
Procedure
Step 1 To register with TAPS, pick up the handset and enter the TAPS extension provided
by your system administrator.
Step 2 Follow the voice prompts.
You might need to enter your entire extension, including the area code.
Step 3 After your phone displays a confirmation message, hang up.
The phone restarts and displays your extension number.
Using Feature Buttons
Your Cisco IP Phone has four feature buttons:
Services buttonDisplays services on your phones LCD screen. These are
services to which you have already subscribed using the Cisco CallManager
User Options web pages. Your system administrator determines the services
that are available to you. For more information, see the Additional Features
and Services section on page 6-3.
Messages buttonProvides access to your voice messaging system. For
more information, see the Using Your Voice Messaging System section on
page 7-1.
Settings buttonDisplays network settings on your phones LCD screen,
plus options for adjusting your phones ringer sound and LCD screen
contrast. For more information, see the Accessing Network Configuration
Data section on page 10-3, the Adjusting the Ringer Volume section on
page 5-2, and the Changing the LCD Screen Contrast section on page 5-4.
1-11
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Chapter 1 Introducing Your Cisco IP Phone
Using Help on Your Phone
Directories buttonDisplays various directories on your phones LCD
screen, including missed, received, and placed calls. You can use each of
these directories to locate phone numbers and you can dial those numbers
from the directories. For more information, see the Searching and Dialing
from the Phone Directory section on page 2-7 and the Viewing and Dialing
from the Phone Logs section on page 2-8.
Using Help on Your Phone
You can push the ? button to quickly access help for specific keys and features.
Help information is displayed on your phones LCD screen.
Using Softkeys
Softkeys correspond to the option tabs displayed along the bottom of your LCD
screen. Softkeys change depending on the status of your phone. For example, you
can see one set of softkey options when you pick up the handset, and another set
when the phone is not in use.
Table 1-1 Getting Help
If you want to... Then...
Learn about a specific button or
softkey
Press the ? button once, then press the button or softkey to display
information about that button or key.
Learn about a specific feature Press the Directories, Settings, or Services buttons to display a list
of available features. Use the Navigation button to scroll through the
list and select a feature. Press the ? button twice quickly to display
information about the selected feature.
Learn about the ? button feature
itself
Press the ? button twice quickly (without first selecting a feature).
This brings up help about using the ? button.
View network statistics about an
active call
Press the ? button twice quickly during the call.
Chapter 1 Introducing Your Cisco IP Phone
Choosing a Menu Item
1-12
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Some of the softkeys enable positioning and corrections to your input. For
example, the >> softkey allows you to reposition your cursor. The << softkey
allows you to delete a character or digit in an entry. Press the << softkey or the
Delete softkey if you make a mistake or need to edit an entry. The Delete softkey
allows you to edit a character or digitit does not delete the entire entry.
Choosing a Menu Item
You can choose menu items on your Cisco IP Phone in more than one way:
Using the Navigation buttonPress the Navigation button (this is the button
with the up and down arrows) to select (or highlight) a menu item. Then press
the Select softkey.
Using an Item NumberYou can press the number key on your phones key
pad that corresponds to the number of the item displayed on the LCD screen.
Use this method to select any menu item that has an item number to the left
of it.
Entering Characters on Your LCD Screen
You might need to enter characters (letters and numbers) on your LCD screen. To
enter such characters, use a corresponding number key. Press the key one or more
times to display a particular letter. For example, press the 2 key one time for a,
twice quickly for b, and three times quickly for c. After you pause, the cursor
automatically advances to allow you to enter the next letter. Press the << softkey
if you make a mistake.
Using the Handset, Speaker and Headset
You can adjust the settings for the handset, speakerphone, and headset
individually. This section includes the following topics:
Using the Handset, page 1-13
Adjusting the Handset Rest, page 1-13
1-13
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Chapter 1 Introducing Your Cisco IP Phone
Using the Handset, Speaker and Headset
Using the Speaker, page 1-14
Using a Headset, page 1-15
Using the Handset
The handset on your Cisco IP Phone functions in the same way as a handset on a
traditional phone:
To place and answer calls with the handset, lift the handset.
To hang up, place the handset back in its cradle.
To switch from the handset to the speaker, press the Speaker button on the
front of your phone during a call, then hang up the handset.
Adjusting the Handset Rest
If you mount your Cisco IP Phone on the wall or use the footstand on the phone,
you can adjust the handset rest to ensure the receiver will not slip out of the cradle.
To adjust the handset rest, see Figure 1-4 and follow the steps below.
Chapter 1 Introducing Your Cisco IP Phone
Using the Handset, Speaker and Headset
1-14
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Figure 1-4 Using the Handset Rest
Using the Speaker
You can use the speaker in conjunction with all of the features on your
Cisco IP Phone.
To place and answer calls using the speaker, press the Speaker button.
To switch from speaker to handset during a call, lift the handset.
Step 1
Set the handset aside and use your thumb and finger to grasp and pull
out the square plastic tab in the handset rest.
Step 2
Rotate the tab 180 degrees.
Step 3
Slide the tab back into the handset rest with the extension protruding
from the top of the tab.
Replace the handset in the rest. The tab hooks into a slot in the handset
to ensure that the handset will not slip out of the rest.
1 2 3
77354
1-15
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Chapter 1 Introducing Your Cisco IP Phone
Using the Handset, Speaker and Headset
Using a Headset
You can use the headset in conjunction with all of the features on your
Cisco IP Phone, including the Volume and Mute buttons. Use these buttons to
adjust the volume to the ear piece and to mute the speech path from the headset
microphone.
To place and answer calls using a headset, plug an approved headset into the back
of the phone base and press the Headset button on the front of your phone.
Figure 1-1 on page 1-4 illustrates the headset port and other cable connection
ports on your phone.
Your phone supports four- or six-wire headset jacks. For information about
purchasing headsets, see the following URL:
http://vxicorp.com/cisco
Chapter 1 Introducing Your Cisco IP Phone
Using the Handset, Speaker and Headset
1-16
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
CHAPTER
2-1
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
2
Making Calls on Your Phone
This chapter describes how to place, answer, and end calls and use other basic
features on your Cisco IP Phone. It covers the following topics:
Understanding Feature Availability, page 2-2
Placing, Answering, and Ending Calls, page 2-2
Getting Notified When a Busy Line Is Available Using Cisco Call Back,
page 2-6
Searching and Dialing from the Phone Directory, page 2-7
Viewing and Dialing from the Phone Logs, page 2-8
Using Mute and Hold, page 2-9
Tracing Suspicious Calls, page 2-10
Extending Speed Dial Functionality, page 2-10
Setting Up and Receiving Priority Calls, page 2-11
Caution Using a cell, mobile, or GSM phone, or two-way radio in close proximity to a
Cisco IP Phone might cause interference. For more information, refer to the
manufacturer's documentation of the interfering device.
Chapter 2 Making Calls on Your Phone
Understanding Feature Availability
2-2
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Understanding Feature Availability
Your company s phone support team determines which features and services are
available to you and how they will be configured. Therefore, some of the features
included in this User Guide might not be available to you or might work
differently on your phone system.
Contact your support desk or system administrator if you have questions about
feature availability.
Placing, Answering, and Ending Calls
This section provides information about placing, answering, and ending calls on
your phone, and using a phone directory and the phone logs. It includes the
following topics:
Placing a Call, page 2-2
Answering a Call, page 2-5
Ending a Call, page 2-6
Tip Lines, or extension numbers, support calls. Look at the LCD screen on your phone
to see how many lines you have. Each line on your phone can support two
connected calls, but only one call can be active at any given time.
Placing a Call
Table 2-1 lists the different ways you can place a call with your Cisco IP Phone.
Table 2-1 Placing a call
If you want to... Then...
Use the receiver Lift the handset and dial a number.
Dial from one of your multiple
lines
Press the line button that corresponds with your extension and dial
a number.
2-3
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Chapter 2 Making Calls on Your Phone
Placing, Answering, and Ending Calls
Place a new call on an active line Press the NewCall softkey and dial a number.
Dial with the phone on-hook
(no dial tone)
From the main screen, dial the number and press the Dial softkey.
(You will not hear a dial tone until after you press the Dial softkey.)
You can also press a line button, the Headset button, or the Speaker
button, or lift the receiver to place the call.
Note If you are dialing with the phone on-hook, you cannot use *
or # as the leading digit. If you need to use these keys, dial
with the phone off-hook.
Use a headset Press the Headset button before or after dialing a number.
Use the speakerphone Press the Speaker button and dial a number.
Redial the most recently dialed
number
Press the Redial softkey. Doing so without lifting the handset
activates the speakerphone or headset. By default, Redial uses your
primary line; however, you can use a secondary line by pressing a
line button and then pressing the Redial softkey.
Use speed-dial numbers
(Supports a maximum of 99
speed-dial numbers and/or
abbreviated dial entries)
Press a Speed dial button before or after going off-hook. You can
extend speed dial functionality by dialing an abbreviated number of
digits that you configured and pressing the AbbrDial softkey.
See the Customizing Your Cisco IP Phone on the Web section on
page 6-3, and the Extending Speed Dial Functionality section on
page 2-10 for more details.
Dial a web-based service from
your phone
Press the Services URL button to enable one-touch access to
information services.
See the Customizing Your Cisco IP Phone on the Web section on
page 6-3.
Dial from a corporate directory Press the Directories button. Select corporate directory. Search for
a listing by using your keypad to enter letters, and press the Search
softkey. To dial from a listing, select it, then press the Dial softkey.
See the Searching and Dialing from the Phone Directory section
on page 2-7 for more details.
Table 2-1 Placing a call (continued)
If you want to... Then...
Chapter 2 Making Calls on Your Phone
Placing, Answering, and Ending Calls
2-4
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Tip If you receive a busy tone or a ring with no answer when you call another
extension, you can use the Cisco Call Back feature to receive notification when
the extension is available. See the Getting Notified When a Busy Line Is
Available Using Cisco Call Back section on page 2-6.
Dial from a phone log Press the Directories button and choose Missed Calls, Received
Calls, or Placed Calls. To dial from a listing, press the number or
scroll to it and go off-hook. To add a prefix or other digits to the
number before dialing, press the EditDial softkey.
See the Searching and Dialing from the Phone Directory section
on page 2-7 for more information.
Dial a Personal Address Book
entry
Press the Services button, then use the Navigation button to choose
the directory number that you want to dial and press the Dial
softkey.
See the Dialing a Personal Address Book Entry section on
page 8-3 for more details.
Dial a Fast Dial number Press the Services button, then use the Navigation button to choose
a Fast Dial number and press the Dial softkey. The Fast Dial service
is accessible from the Services menu.
See the Dialing a Fast Dial Entry section on page 8-6 for more
details.
Dial from a corporate directory
web page
Click on a hyperlinked telephone number in a company directory to
make calls from the web interface and desktop applications. Refer
to Customizing Your Cisco IP Phone on the Web for additional
details.
Table 2-1 Placing a call (continued)
If you want to... Then...
2-5
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Chapter 2 Making Calls on Your Phone
Placing, Answering, and Ending Calls
Answering a Call
Table 2-2 lists ways to answer an incoming call:
Table 2-2 Answering a Call
If you want to... Then...
Answer with the handset Lift the handset.
Answer using a headset Press the Headset button if it is not lit. If the Headset button is lit,
press the Answer softkey or the line button of the incoming call.
Answer with the speakerphone Press the Answer softkey, the Speaker button, or the line button.
Set up your phone to
automatically answer calls
Ask your system administrator to set up the AutoAnswer feature for
your line(s). The phone will automatically answer the call when it
is received This feature can be set up to work with your headset or
with your speakerphone.
Set up your phone to
immediately redirect a call to
your voice messaging system or
to the voice messaging system of
the called party
To redirect a call to your voice messaging system, press the iDivert
softkey while you are receiving a call, from a call-on-hold, or from
a connected call. To redirect a call to the called partys voice
messaging system, press the iDivert softkey to redirect an outgoing
call that is connected or on hold.
See the Sending Calls to a Voice Messaging System section on
page 3-8 for more details.
Answer an incoming call that is
ringing on another extension
within your group
Press an available line button on your phone and then press the
PickUp softkey. The call rings on your phone. (A Call Pickup
group is defined by your system administrator.) See the
Answering Calls that are Ringing on Another Extension Using Call
Pickup section on page 3-5.
Answer an incoming call that is
ringing on another extension
outside of your group
Press an available line button and then press the GPickUp softkey
on your phone. Dial the call pickup group number assigned by your
administrator, and answer the call that is redirected to your phone.
See the How to Pick Up Calls Outside of Your Group section on
page 3-6.
Keep your call information
private on a shared line call
Press the Privacy button after you select an incoming call.
See the Keeping Your Call Information Private section on
page 4-7 for more details.
Chapter 2 Making Calls on Your Phone
Getting Notified When a Busy Line Is Available Using Cisco Call Back
2-6
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Ending a Call
Table 2-3 lists ways to end a call.
Getting Notified When a Busy Line Is Available
Using Cisco Call Back
If you call an extension and the line is busy or the call goes unanswered, you can
use the Cisco Call Back feature to receive notification when the extension is
available to take a call.
Procedure
Step 1 Call an extension. While you hear the busy tone or ringing tone, press the
CallBack softkey.
A CallBack activation confirmation message displays.
Note Cisco Call Back notification will fail if the called party has forwarded all
calls to another extension.
Step 2 Press the Exit softkey to close the confirmation screen, or press the Cancel
softkey to cancel the call back notification.
Step 3 To verify the status of the call back notification, press the CallBack softkey while
your phone is idle.
Table 2-3 Ending a Call
If you are using... Then...
The handset Return the handset to the cradle, or press the line button or the
EndCall softkey.
A headset Press the Headset button or the line button or the EndCall softkey.
(If you want to keep the headset mode activated for use with
AutoAnswer, press the line button or the EndCall softkey.)
The speakerphone Press the Speaker button or the line button or the EndCall softkey.
2-7
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Chapter 2 Making Calls on Your Phone
Searching and Dialing from the Phone Directory
A confirmation message is displayed.
Press the Exit softkey to close the confirmation screen or press the Cancel softkey
to cancel call back notification.
Step 4 When the extension you called is available to receive a call, you receive an audio
and visual alert from your phone. Press Dial to dial the number.
Searching and Dialing from the Phone Directory
Your phone might come configured with a searchable corporate or local phone
directory that allows you to easily find and dial phone numbers of colleagues.
Follow these steps to view or dial from a directory in your company.
Procedure
Step 1 Press the Directories button.
Step 2 Use the Navigation button to select the desired directory from the Directories
menu, then press the Select softkey.
Step 3 Enter search criteria to retrieve a record (see the Entering Characters on Your
LCD Screen section on page 1-12 for information on entering characters into
your phone.)
Step 4 To place a call from any directory, use the Navigation button to select the record,
then press the Dial softkey.
Note You might need to use the EditDial softkey to add digits to the front of
the number. For example, if the call was from an outside, long-distance
caller, you might need to add the digits 9-1 to the front of the number.
Then, press the Dial softkey.
Step 5 Press the Exit softkey twice to exit the Directory menu. Alternatively, you can
press the Directories button one time to exit the Directory menu.
Chapter 2 Making Calls on Your Phone
Viewing and Dialing from the Phone Logs
2-8
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Viewing and Dialing from the Phone Logs
If your phone display indicates that you have missed calls, you can use the Missed
Calls option on the Directory menu to view your call history and to call back the
person whose call you missed. Likewise, you can view call histories and place
calls from the Received Calls and Placed Calls directories.
If the network shuts down or is reset, you might lose your call history records. If
you use Cisco CallManager Extension Mobility (see Chapter 9, Logging In to
Your Extension Using the Cisco CallManager Extension Mobility Feature), the
call history is available only for times you are logged into the phone. Also, there
is a limit on the number of call history records that can be stored. Your system
administrator can provide information on this limit.
You can delete all records in the Missed, Received, or Placed directories from the
Directories menu. Use the Navigation button to select the directory that you want
to delete and pressing the Clear softkey.
Follow these steps to view or dial from a call log on your phone:
Procedure
Step 1 Press the Directories button.
Step 2 Use the Navigation button to select the desired directory, and press the Select
softkey.
Step 3 To place a call from any directory, use the Navigation button to select the record,
then press the Dial softkey.
Note Use the EditDial softkey to add digits to the front of the number. (For
example, if the call was from an outside, long-distance caller, you might
need to add the digits 9-1 to the number before dialing.) Then, press the
Dial softkey.
Step 4 Press the Exit softkey twice to exit the Directory menu.
2-9
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Chapter 2 Making Calls on Your Phone
Using Mute and Hold
Using Mute and Hold
Table 2-4 lists ways to use the Mute and Hold features.
Table 2-4 Using Mute and Hold
If you want to... Then...
Mute a call Press the Mute button to mute the handset, headset, or
speakerphone during a call. Mute temporarily disables your phones
microphone so you can hear other parties on the call but they cannot
hear you.
To toggle mute off, press Mute again.
Put a call on hold Use the Navigation button to select the call you want to put on hold,
then press the Hold softkey. The call remains active but the
connected parties on the call cannot hear each other. You can answer
other calls while a call is on hold.
Note Using the Hold feature generates music or a beeping tone.
For this reason, avoid putting a conference call on hold.
Resume a call on hold Press the Resume softkey.
Have multiple calls on hold Use the Navigation button to select the desired call, then press
Resume.
Have multiple calls on multiple
lines on hold
Press the line button for the line to which you want to switch, and
use the Navigation button to select the desired call. Press Resume.
If you cannot use the Navigation button because only one line is
displayed on your phones LCD screen, press the line button next to
the call that you want to resume.
If your phone opens a new line when you press the line button, press
the EndCall softkey to return to the desired call.
Tip If you are using multiple lines and want to see the phone
number for a call you have on hold, press the ? button
followed by the line button of the call on hold.
Chapter 2 Making Calls on Your Phone
Tracing Suspicious Calls
2-10
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Tracing Suspicious Calls
If you receive a suspicious call, you can notify your system administrator by using
the Malicious Call Identification (MCID) feature. This feature allows you to trace
the source of a suspicious call, through either a feature button or a softkey, and
identify the call for further action.
Note MCID is a feature that your system administrator must configure to your user
profile and/or to the IP phone that is associated with your user ID. If you use the
Cisco CallManager Extension Mobility service, the MCID feature is available
only on an IP phone that you are logged into. Check with your system
administrator to find out if this feature has been enabled for you.
If you see the MCID softkey available on your phone, you can press this softkey
while you are connected to a call or while you are on a conference call.
If you answer a call and are uncertain about the caller information, use the
MCID feature. Press the MCID feature button (or softkey) that was assigned
by your system administrator while continuing your existing call.
You will see a visual indication of the calling line ID and calling name of the
caller, along with an audible confirmation tone that the call was identified and
registered.
Extending Speed Dial Functionality
You can enhance and extend the speed dial functionality on your phone by using
the abbreviated dialing feature. Abbreviated dialing allows you to quickly call a
number that you have configured. Press an abbreviated dial entry index number
(one or two digits) while your phone is on-hook, and then press the AbbrDial
softkey. (The AbbrDial softkey is displayed once you start to press the digits.)
You can configure up to 99 speed dial and/or abbreviated dial entries from the
Cisco CallManager User Options web page. Some of the speed dials can be
assigned to the speed-dial buttons on your phone. The entries that are not assigned
to the speed-dial buttons are available for use with the abbreviated dialing feature.
2-11
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Chapter 2 Making Calls on Your Phone
Setting Up and Receiving Priority Calls
Follow these steps to use abbreviated dialing:
Before You Begin
Log in to the User Options web page to configure your abbreviated dialing
numbers. For instructions, see the Logging on to the User Options Web Pages
section on page 6-1 and the Customizing Your Cisco IP Phone on the Web
section on page 6-3.
Procedure
Step 1 Dial a speed-dial index number while your phone is on-hook.
The AbbrDial softkey appears on your phone.
Step 2 Press the AbbrDial softkey.
The number associated with the abbreviated dialing index number that you
entered is dialed.
Setting Up and Receiving Priority Calls
You can see the priority, or precedence, level associated with a call by using the
multilevel precedence and preemption (MLPP) feature.
Note The MLPP feature must be configured by your system administrator. Check with
your system administrator to find out if this feature has been enabled for you.
Precedence is the priority associated with a call. (Higher priority calls are
listed at the top of your call list.)
Preemption is the process of ending an existing, lower priority call while
allowing a higher priority call to be accepted by the called party.
If you are authorized to use Extension Mobility and MLPP, you can use MLPP on
another phone that is authorized to use the Extension Mobility feature.
Chapter 2 Making Calls on Your Phone
Setting Up and Receiving Priority Calls
2-12
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Setting Up a Priority Call
When you set up a precedence call, you select a priority level for the call based
on a preconfigured pattern of numbers assigned by your system administrator.
(Precedence levels are selected on a per-call basis.)
Receiving a Priority Call
A precedence call is a call with a higher priority than an existing call.
When you receive a precedence call, an icon indicating the priority level is
displayed on your phones LCD screen and you will hear a special ring tone. To
connect a precedence call, you must hang up the phone. You will hear a priority
ring tone, and the precedence call is connected.
Follow these steps to set up and receive an MLPP call.
Procedure
Step 1 Dial the MLPP call using the numbers configured by your system administrator
(for example, dial 90 followed by the extension).
You will hear the preemption tone if the call is to be preempted by the higher
priority call.
Step 2 If you are the called party, acknowledge the priority call by hanging up the phone,
which preempts the existing call.
You will hear a priority ringing tone, and the priority call is connected.
If you do not acknowledge the priority call, the call is redirected. See the MLPP
Messages section on page 2-13 for additional information.
2-13
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Chapter 2 Making Calls on Your Phone
Setting Up and Receiving Priority Calls
MLPP Exceptions:
Will not drop or preempt an active call on the Cisco IP Phones 7960G and
7940G.
Is not supported on conference bridges or with Cisco IP Manager Assistant
(Cisco IPMA).
MLPP Messages
If a priority call cannot be connected between the parties, you might hear
messages similar to the following:
A message indicating that an invalid priority level was requested.
A message indicating that the priority call could not be completed. This could
be because of multiple priority calls of equal or higher value or the
unavailability of network resources to connect the call.
A message indicating that the called partys phone is busy and does not
support MLPP.
Chapter 2 Making Calls on Your Phone
Setting Up and Receiving Priority Calls
2-14
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
CHAPTER
3-1
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
3
Redirecting Calls on Your Phone
This chapter provides instructions for redirecting calls on your phone. It covers
the following topics:
Transferring Calls, page 3-1
Storing and Retrieving a Call Using Call Park, page 3-4
Answering Calls that are Ringing on Another Extension Using Call Pickup,
page 3-5
Forwarding Calls to Another Extension, page 3-6
Sending Calls to a Voice Messaging System, page 3-8
Transferring Calls
Transfer redirects a connected call. There are multiple ways to transfer a call.
Transferring a Call to Another Extension
Follow these steps to transfer a call to another phone.
Procedure
Step 1 During a call, press the Transf softkey. This puts the call on hold.
Step 2 Dial the number or office extension to which you want to transfer the call.
Chapter 3 Redirecting Calls on Your Phone
Transferring Calls
3-2
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Step 3 When it rings on the other end, press Transf again. Or, when the party answers,
announce the call and then press Transf. (This is a consult transfer.)
Step 4 If you are using a handset, hang up.
If the party refuses the call, press the Resume softkey to return to the original call.
Directly Transferring Your Calls
Direct Transfer provides another way to transfer a call. Use this feature with the
DirTrfr softkey to join two established calls into one call and then immediately
drop yourself from the call (no consult transfer). An established call is a
call-on-hold or an active (connected) call.
When you use direct transfer, you must select two calls on the same shared line
appearance.
Scenarios for Directly Transferring Your Calls
You can use direct transfer to join calls in three scenarios:
To join a call-on-hold with another call-on-hold
To join a call-on-hold with a connected call
To join two calls that are on hold with a connected call
You cannot use direct transfer to:
Join more than two calls.
Join two ad hoc conference calls.
Join an ad hoc conference call and a barged call.
Using Direct Transfer to Join a Call-on-Hold with Another Call-on-Hold
Procedure
Step 1 Use the Navigation button to select the first call-on-hold.
Step 2 Press the Select softkey.
3-3
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Chapter 3 Redirecting Calls on Your Phone
Transferring Calls
The selected call displays a checkmark indicator on the phones LCD screen.
Step 3 Use the Navigation button to select the second call-on-hold.
The call will be highlighted on the phone and added to the direct transfer.
Step 4 Press the DirTrfr softkey.
The two calls that were on hold are joined into one call.
Using Direct Transfer to Join a Call-on-Hold with a Connected Call
Procedure
Step 1 Use the Navigation button to select the call-on-hold.
Step 2 Press the Select softkey.
The selected call displays a checkmark indicator on the phones LCD screen.
Step 3 Use the Navigation button to select the connected call.
The call will be highlighted on the phone.
Step 4 Press the DirTrfr softkey from either the connected call or the call-on hold.
The connected call is joined with the call-on-hold.
Note When you press the DirTrfr softkey from a connected call or from another
call, that call is automatically included in the direct transfer (if not
specifically selected).
Using Direct Transfer to Join Two Calls on Hold with a Connected Call
Procedure
Step 1 Use the Navigation button to select the first call-on-hold.
Step 2 Press the Select softkey.
The selected call displays a checkmark indicator on the phones LCD screen.
Chapter 3 Redirecting Calls on Your Phone
Storing and Retrieving a Call Using Call Park
3-4
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Step 3 Use the Navigation button to select the second call-on-hold.
The call will be highlighted on the phone and added to the direct transfer.
Step 4 Press the DirTrfr softkey.
The first and second calls that were on hold are joined into one call.
Storing and Retrieving a Call Using Call Park
You can park a call when you want to store the call before retrieving it from
another phone in the Cisco CallManager system (for example, a phone in someone
elses office or in a conference room). Call park numbers are preconfigured for
this purpose by your system administrator.
Procedure
Step 1 During an active call, press the more softkey, then the Park softkey.
Step 2 Press Park. The LCD screen displays the special call park number where the call
is stored. If the screen does not display a call park number, the call park feature is
not available to you.
Step 3 Make a note of the call park number, then hang up. The call is parked at that
number, allowing you to retrieve it from another phone.
Step 4 To retrieve the parked call from any phone in the Cisco CallManager system, dial
the call park number where the call is parked.
Note You have a limited amount of time to retrieve the parked call before it
reverts to ringing at its original destination. See your system
administrator for this time limit.
3-5
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Chapter 3 Redirecting Calls on Your Phone
Answering Calls that are Ringing on Another Extension Using Call Pickup
Answering Calls that are Ringing on Another
Extension Using Call Pickup
You can answer an incoming call that is ringing on an extension other than your
own by using the call pickup feature. This feature allows you to answer the call
on your phone.
There are two types of call pickup available on the Cisco IP Phone, as described
in these topics:
How to Pick Up Calls Within Your Group, page 3-5
How to Pick Up Calls Outside of Your Group, page 3-6
Note Call pickup and group call pickup are optional features configured by your system
administrator; your phone does not support these features by default.
How to Pick Up Calls Within Your Group
Call pickup allows you to pick up incoming calls within your own group. A
group is any consolidation of Cisco IP Phone extensions, as defined by your
system administrator. For example, your group might contain coworkers in
neighboring offices or cubes.
Activate call pickup so that an incoming call delivered to another extension in
your group rings on your extension.
Procedure
Step 1 Press any available line button on your Cisco IP Phone.
Step 2 Press the PickUp softkey. The call now rings on your phone.
Step 3 Answer the incoming call.
Chapter 3 Redirecting Calls on Your Phone
Forwarding Calls to Another Extension
3-6
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Tip If there is more than one incoming call involved when you activate call pickup,
the first unanswered call will ring at your phone.
How to Pick Up Calls Outside of Your Group
Group call pickup allows you to pick up incoming calls within your own group or
in other groups. A group might contain coworkers in neighboring offices or
cubes.
You must dial the appropriate call group pickup number when using this feature.
A call group pickup number is provided to you by your system administrator.
Procedure
Step 1 Press any available line button.
Step 2 Press the GPickUp softkey.
Step 3 Dial the required call group pickup number.
Step 4 Answer the incoming call that is redirected to your phone.
Step 5 To pick up a call using a different call group pickup number, hang up and begin
again at Step 1.
Tip If there is more than one incoming call involved when you activate call group
pickup, you receive the first unanswered call. If there is no unanswered call in the
group, or if you dial an invalid group number, you receive a fast busy tone.
Forwarding Calls to Another Extension
Call forwarding allows you to redirect all incoming calls from your
Cisco IP Phone to another number.
Use call forwarding to:
3-7
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Chapter 3 Redirecting Calls on Your Phone
Forwarding Calls to Another Extension
Send incoming calls to another number where you can answer the calls (for
example, if you are going to be working in an alternate office).
Send incoming calls directly to your voice messaging system. Your desk
phone does not ring when calls are routed to your voice messaging system
through the call forwarding feature.
Call forwarding can send your calls to another Cisco IP Phone or to a traditional
analog phone.
If there is no answer at the forwarded number, either by a person by a voice
messaging system, the call will be sent back to your voice messaging system.
Setting Up Call Forwarding on Your Phone
Follow these steps to set up call forwarding on your phone.
Note You can also set up and cancel call forwarding from the web. See the
Customizing Your Cisco IP Phone on the Web section on page 6-3 and refer to
Customizing Your Cisco IP Phone on the Web for additional details.
Procedure
Step 1 Press the CFwdAll softkey. You should hear two beeps.
Step 2 Enter the number to which you want to forward all of your calls, exactly as you
would if you were placing a call to that number.
Note For example, enter an access code such as 9 or the area code, if necessary.
Your system administrator might restrict the call forwarding feature to
numbers within your company.
After you enter the number, an animated phone icon with a flashing right arrow
appears in the upper-right corner of the LCD screen. The LCD screen also
displays a message confirming the number or extension to which your calls are
being forwarded.
Chapter 3 Redirecting Calls on Your Phone
Sending Calls to a Voice Messaging System
3-8
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Step 3 To cancel call forwarding, press the CFwdAll softkey.
Tip You can use the User Options web pages to set up call forwarding when you are
not at your phone, or to use call forwarding to send all of your incoming calls
directly to your voice messaging system without causing your desk phone to ring.
Refer to the procedures in Customizing Your Cisco IP Phone on the Web.
Canceling Call Forwarding on Your Phone
To cancel call forwarding from your phone, press the CFwAll softkey.
Sending Calls to a Voice Messaging System
You can immediately redirect incoming or outgoing calls to a voice messaging
system by using the Immediate Divert feature on your phone.
Table 3-1 provides instructions for using Immediate Divert.
Tips for using Immediate Divert
Immediate Divert does not support Multilevel Precedence and Preemption.
Table 3-1 Sending a Call to a Voice Messaging System
If you want to... Then...
Send all of your incoming calls,
or selectively send a call, to your
voice messaging system from
your phone.
Press the iDivert softkey while you are receiving a call, from a
call-on-hold, or from a connected call. The call is immediately sent
to your voice messaging mail box; the calling party hears your voice
messaging mail box greeting.
Send an outgoing call to the
called partys voice messaging
system from your phone.
Press the iDivert softkey on an outgoing call that is connected or on
hold. The call is immediately sent to the voice messaging mail box
that is assigned to the called party; you will hear the called partys
voice messaging mail box greeting.
3-9
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Chapter 3 Redirecting Calls on Your Phone
Sending Calls to a Voice Messaging System
Immediate Divert is not supported when Call Forward All (CFA) and
Call Forward Busy (CFB) are activated.
Immediate Divert cannot redirect a call to a busy voice messaging system.
If you press the iDivert softkey while you are participating in a conference
call (ad hoc conference, Meet-me conference, or Join conference), the
conference participants hear your voice messaging mail box greeting.
Table 3-2 on page 3-9 shows the messages that might be displayed on your IP
phones LCD screen to indicate the status of an immediate divert action.
Table 3-2 Immediate Divert Status Messages
Message... Meaning...
Immediate Divert The call was successfully sent to a voice messaging mail box.
Key is not active The voice messaging profile of the last called party does not have a
voice messaging system access number.
Temporary failure The voice messaging system is not working or there is a network
problem.
Busy The voice messaging system is busy.
Chapter 3 Redirecting Calls on Your Phone
Sending Calls to a Voice Messaging System
3-10
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
CHAPTER
4-1
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
4
Making Conference Calls on Your Phone
Your Cisco IP Phone supports conference calls, enabling you to talk with multiple
parties at the same time. When you are on a conference call, you can use regular
phone features such as Mute, Hold, Transfer, and speakerphone.
This chapter covers the following topics:
Placing a Conference Call, page 4-1
Viewing Participants in a Conference Call, page 4-2
Selecting Participants to Join a Conference Call, page 4-3
Adding Your Line to a Shared Line Call, page 4-4
Keeping Your Call Information Private, page 4-7
Using Meet-me Conferences, page 4-8
Placing a Conference Call
Follow these steps to turn a call into a conference call.
Procedure
Step 1 During a call, press the more softkey, then the Confrn softkey. Doing so
automatically activates a new line and puts the first party on hold.
Step 2 Place a call to another number or extension.
Step 3 When the call connects, press Confrn again to add the new party to the conference
call.
Chapter 4 Making Conference Calls on Your Phone
Viewing Participants in a Conference Call
4-2
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Repeat these steps to add parties to the conference call.
Once the conference call initiator disconnects from the call, no additional parties
can be added.
Tip You can drop the last party added by pressing the RmLstC softkey, if the
feature is available.
Viewing Participants in a Conference Call
The Conferee List feature allows you to see a list of names and directory numbers
for participants in an ad hoc conference by pressing the ConfList softkey. (Ad hoc
conferences enable the party who initiated the conference to add or remove
conference participants.) Your Cisco IP Phone LCD screen displays your
connection status to the conference.
Only participants in an ad hoc conference can use the ConfList softkey. The party
who initiates the conference call has the additional capability of removing any
conference participant by pressing the Remove softkey.
Follow these steps to view a list of participants in an ad hoc conference call.
Procedure
Step 1 Use the Navigation button to select the active ad hoc conference call.
Step 2 Press the ConfList softkey to display the list of conference participants.
The list is sorted with the last participant shown at the top and the conference call
initiator shown at the bottom (indicated by an * on the LCD screen).
Step 3 While viewing the list, press the Update softkey to get an updated list of
participants.
Step 4 Press the Exit softkey to exit the list and return to the conference call screen.
Step 5 If you initiated the conference call and need to remove a participant, use the
Navigation button to select the participant name and press the Remove softkey.
4-3
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Chapter 4 Making Conference Calls on Your Phone
Selecting Participants to Join a Conference Call
When only two participants remain in a conference, the conferee list is cleared
and the conference is ended. The two remaining participants are reconnected as a
direct call.
Selecting Participants to Join a Conference Call
You can use the Join feature to join all parties in established calls (active or on
hold) into one call by using the Join softkey. The Join feature does not initiate a
consultation call nor put the active call on hold.
Follow these steps to join more than one call to an ad hoc conference call.
Procedure
Step 1 While you are on a call, use the Navigation button to select the first call to join.
The call is highlighted on the phone.
Step 2 Press the Select softkey.
On the LCD screen, a check mark is displayed next to the call.
Step 3 Use the Navigation button to select another call.
The call is highlighted on the phone.
Step 4 Press the Select softkey.
On the LCD screen, a check mark is displayed next to the call.
Step 5 From one of the selected calls, press the more softkey, then the Join softkey.
The selected calls are joined into one ad hoc conference call.
Step 6 Repeat these steps to add parties to the conference call.
If you initiated the call, you can add or drop participants of the joined call.
Step 7 Press the Endcall softkey to drop your connection from the call.
If you initiated the call, you can disconnect at any time and the conference call
remains active.
Chapter 4 Making Conference Calls on Your Phone
Adding Your Line to a Shared Line Call
4-4
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Note When you press the Join softkey from a connected call or from another
call, that call is automatically included in the conference call (if not
specifically selected).
Tips for using the Join feature:
A minimum of two calls must be selected.
You can connect up to 16 participants into one conference call.
The connection of two or more conference calls is not supported.
All calls selected must be on the same line appearance when you initiate join
from your phone (except when you use Cisco IP Manager Assistant
(Cisco IPMA), which can select calls across line appearances).
Adding Your Line to a Shared Line Call
If you use a shared line, you can add yourself to an established call by using the
Barge feature.
Understanding Shared Lines
Your system administrator might assign you a shared line. Shared lines can be
applied to multiple phones or multiple parties can share a line.
One party applies a shared line to multiple phones that are usedFor
example, your shared line with extension 2230 applies to your desk phone and
your mobile phone. You can also log into a phone in your lab enabling the lab
phone to temporarily share your extension as well. In this case, an incoming
call to extension 2230 rings on your desk phone, lab phone and mobile phone.
You can use any of these phones to answer the call.
Multiple parties share a lineFor example, you are a manager who shares a
line and extension number with your assistant. An incoming call to the
extension rings on both phones. If your assistant answers the call, you can use
a shared line feature called Barge to add yourself to the connected call.
4-5
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Chapter 4 Making Conference Calls on Your Phone
Adding Your Line to a Shared Line Call
Support for Conference Modes
Cisco IP Phones support barge in two conference modes:
Using the Barge softkey and conference resources that are built into the
phone. Barge allows you to join an in-progress call with minimal interruption
to the call. When you use Barge, other parties on the call hear a beep tone
announcing your presence. Barge does not change the original call
information display. You cannot add additional callers to a barged call. When
you hang up, the remaining parties hear a disconnect tone, and the original
call continues. The maximum number of parties for a Barge call is limited to
three.
Using the cBarge softkey and shared conference resources. cBarge allows you
to join an in-progress call and convert it to a standard conference call. With
cBarge, every party is treated as an ad hoc conference call participant; all call
participants have the same features available as in standard conferences.
When you use cBarge, other parties on the call hear a tone and brief
interruption in the call; the original call information changes on the LCD
screen. When you hang up, the call remains as a conference call provided at
least three participants remain. cBarge allows multiple parties (3-16) to barge
into a call.
Note The Barge softkey is enabled by default. Your system administrator might
determine that Barge or cBarge is the more appropriate option for your company
and then assign that specific softkey to your phone. Check with your system
administrator to find out if Barge or cBarge has been enabled for you.
Follow these steps to add yourself to a call on one of your shared lines:
Procedure
Step 1 Select an active call on one of your shared lines.
Step 2 If your system administrator assigned the Barge softkey to your phone, follow
Step 3 and Step 4. If your system administrator assigned the cBarge softkey to
your phone, follow Step 5 and Step 6. See the Support for Conference Modes
section on page 4-5 for information about Barge and cBarge.
Chapter 4 Making Conference Calls on Your Phone
Adding Your Line to a Shared Line Call
4-6
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Step 3 Press the Barge softkey, if your system administrator assigned Barge to your
phone.
The phone creates a conference call and sends a beep tone to all of the conference
participants. (If the barge fails, the original call remains active.)
Note Contact your system administrator if a message similar to
No Conference Bridge Available appears on your phones LCD screen
when you press the Barge softkey.
Step 4 To end the conference, hang up.
The remaining parties hear a disconnect tone, and the original call continues. If
the target shared line call that was barged hangs up, the call returns to a two-party
call between the original connected party and the party who initiated the barge. If
the original party (who was connected to the target shared line party) hangs up,
the Barge call is terminated and all parties are disconnected.
Note You are disconnected from a barged call if the target shared line call is put on hold,
transferred, or converted to a conference call.
Step 5 Press the cBarge softkey, if your system administrator assigned cBarge to your
phone.
The phone creates an ad hoc conference call, which changes the original call
information display.
Step 6 To end the conference, hang up.
If any party hangs up and only two parties remain in the conference call, the
remaining two parties are connected as a two-party direct call.
When you use Barge:
The target shared line cannot be on two barged calls at the same time.
The party who initiated the barge is dropped when the target shared line puts
the barged call on hold.
The party who initiated the barge is dropped when the target shared line
answers an incoming call.
4-7
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Chapter 4 Making Conference Calls on Your Phone
Keeping Your Call Information Private
Keeping Your Call Information Private
If you use a shared line, you can keep your call information private from users
who share your lines by using the Privacy feature.
Note The Privacy feature must be configured by your system administrator. Check to
see if this feature has been enabled for your phone.
Follow these steps to make your call information private on shared lines.
Procedure
Step 1 Select an incoming call on one of your shared lines.
Step 2 Press the Privacy button to make the call private.
You can press the Privacy button before or after you answer a call.
Table 4-1 Enabling and Disabling Your Call Privacy
When Privacy is... Then...
Enabled
(This setting affects all lines on
the phone.)
Both a Privacy button and a status symbol appear on your
phone. An LED lights to indicate that Privacy is enabled.
Your phones call status information is removed from all
phones that share lines.
You cannot use barge and other shared line-related features on
your calls from a phone that shares your lines.
The real-time call information is not displayed on your phone,
but the call history (missed, placed, or received calls) is
displayed on phones that share your lines.
Disabled
(This setting affects all lines on
the phone.)
Your phones call status information is displayed on all phones
that share your lines.
You can use barge and other shared line-related features on your
calls from a phone that shares your lines.
Chapter 4 Making Conference Calls on Your Phone
Using Meet-me Conferences
4-8
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Note The privacy setting prevents your call status information from being
displayed on the shared line and it prevents another party from barging
into your call.
Using Meet-me Conferences
Your Cisco IP Phone supports Meet-me conferences. A Meet-me conference
allows other callers to dial into the conference call. A Meet-me conference
requires a special conference number which your system administrator
preconfigured for this purpose.
This section covers these topics:
Establishing a Meet-me Conference, page 4-8
Joining a Meet-me Conference, page 4-9
Establishing a Meet-me Conference
Follow these steps to establish a Meet-me conference call.
Before You Begin
Contact your system administrator for the necessary Meet-me conference number
or numbers.
Procedure
Step 1 Press the more softkey until you see the Meet-me softkey.
Step 2 Press the Meet-me softkey.
Step 3 Dial the Meet-me conference number.
Step 4 Follow the voice instructions to establish the Meet-me conference.
4-9
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Chapter 4 Making Conference Calls on Your Phone
Using Meet-me Conferences
Joining a Meet-me Conference
To join a Meet-me conference, dial the Meet-me conference number provided by
the Meet-me conference initiator. You are connected to the conference after the
conference initiator dials in and establishes the conference. You do not need to
press the Meet-me softkey on your Cisco IP Phone.
Chapter 4 Making Conference Calls on Your Phone
Using Meet-me Conferences
4-10
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
CHAPTER
5-1
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
5
Customizing Settings on Your Phone
This chapter describes the ways in which you can personalize settings, such as
volume and ringer sound, for your Cisco IP Phone. It covers the following topics:
Adjusting the Handset, Speakerphone, and Headset Volume, page 5-1
Adjusting the Ringer Volume, page 5-2
Personalizing the Ringer Sound, page 5-2
Changing the LCD Screen Contrast, page 5-4
Adjusting the Handset, Speakerphone, and Headset
Volume
You can adjust the volume of the caller for the handset, speakerphone, and headset
individually. When you change the volume for one, the others are not affected.
Follow these steps to adjust the volume on the handset, speakerphone, or headset.
Procedure
Step 1 Press the up or down Volume button when the handset, speakerphone, or headset
is in use.
Chapter 5 Customizing Settings on Your Phone
Adjusting the Ringer Volume
5-2
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Note If you press the Volume button when none of these are in use, you are
adjusting the ringer volume. For details, see the Adjusting the Ringer
Vo lum e section on page 5-2.
Step 2 To save this volume setting for future calls, press the Save softkey.
If you adjust the volume during a call without pressing Save, you are changing the
volume level only for the duration of that particular call; on subsequent calls, the
volume level will revert to the previously saved setting.
Adjusting the Ringer Volume
To change the volume used by the ringer:
Press the up or down Volume button while you are not on a call.
Continue to press the Volume button to hear sample rings and to adjust the
volume to the desired level. The ringer volume is automatically saved.
Personalizing the Ringer Sound
You can change the sound your phone makes when it rings to suit your tastes and
to help you differentiate between your phone ringing and another, nearby, phone
ringing or to differentiate between different lines on your own phone.
Follow these steps to change the sound used by the ringer.
Procedure
Step 1 Press the Settings button.
Step 2 From the Settings menu, use the Navigation button to select Ring Type and press
the Select softkey.
You will see two different ring types on the LCD screen: default ring and a ring
type for your line.
5-3
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Chapter 5 Customizing Settings on Your Phone
Personalizing the Ringer Sound
Step 3 To set the ring type for the default ring tone, use the Navigation button to
highlight Default Ring and press the Select softkey.
Step 4 Use the Navigation button to scroll through the list of ring types and press the
Play softkey to hear the selected ring.
Step 5 When you find the ring you want, press the Select softkey to select the
corresponding check box.
Step 6 Press the OK softkey to accept and save your ringer selection.
Step 7 If you have multiple lines, use the Navigation button to scroll through the list of
your lines. When you find the line you want to configure, press the Select softkey.
Note You can use only six different ring tones on your phone. If you have more
than six lines, some of your lines must share a ring tone.
Step 8 Use the Navigation button to scroll through the list of ring types and press the
Play softkey to hear the selected ring type.
Step 9 When you find the ring you want, press the Select softkey to check the
corresponding check box.
Step 10 Press the OK softkey to accept and save your ringer selection.
To set the ring tone for your line to match the default ring tone, select the Default
softkey.
Step 11 Press the Exit softkey to save all of your settings and to exit the Settings menu.
Chapter 5 Customizing Settings on Your Phone
Changing the LCD Screen Contrast
5-4
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Changing the LCD Screen Contrast
To improve the readability of the LCD screen, follow these steps to adjust the
contrast.
Procedure
Step 1 Press the Settings button.
Step 2 From the Settings menu, use the Navigation button to highlight Contrast and
press the Select softkey.
Step 3 Perform one of the following:
To set the desired contrast level on your base phonepress the Up or Down
softkeys (or the Volume buttons). Press the OK softkey, then the Save softkey.
If you have an attached Cisco IP Phone 7914 Expansion Module and want to
adjust the contrast, select Expansion Module(s) and follow the same
procedure used for your base phone.
Step 4 To restore contrast settings, from the Settings menu use the Navigation button to
highlight Contrast and perform one of the following:
To restore your previously saved contrast settingpress the more softkey,
then the Restore softkey.
To restore the factory default contrast settingpress the more softkey, then
the Default softkey.
Step 5 Press the Save softkey to accept and save your changes, and to exit the Settings
menu.
CHAPTER
6-1
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
6
Customizing Your Phone on the Web
You can customize your phone on the web using the Cisco CallManager
User Options web pages. This chapter includes the following topics:
Logging on to the User Options Web Pages, page 6-1
Changing your Password or PIN, page 6-2
Customizing Your Cisco IP Phone on the Web, page 6-3
Note If you use the Cisco CallManager Extension Mobility service, changes that you
make from the User Options web pages are maintained in your device profile.
Logging on to the User Options Web Pages
Follow these instructions to log on and to access the User Options web page main
menu.
Procedure
Step 1 From your web browser, access the URL provided by your system administrator.
The Cisco CallManager User Options Log On page appears.
Step 2 Enter your user ID and your password and click Log On. Your user ID and
password are provided by your system administrator.
The Cisco CallManager User Options Menu page appears.
Chapter 6 Customizing Your Phone on the Web
Changing your Password or PIN
6-2
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Step 3 From the Select a device to configure drop-down list, select your phone model
or, if applicable, your Cisco CallManager Extension Mobility device profile
(which usually contains the prefix EM).
The menu is context-sensitive and displays options appropriate for the device or
device profile that you have selected.
Changing your Password or PIN
You can change your login password for the User Options web page or your PIN
for Cisco IP Phone Services. Follow the appropriate procedure to change your
password or PIN.
Procedure for Changing Your Password
Step 1 From the User Options main menu, select your phone or, if applicable, your
Cisco CallManager Extension Mobility device profile from the Select a device to
configure drop-down list.
Step 2 Click Change your Password.
The Change Your Password page appears.
Step 3 Fill in the fields as follows:
a. In the Current Password text box, enter your current password.
b. In the New Password text box, enter your new password.
c. In the Confirm Password text box, enter your new password again to confirm
it.
Step 4 Click Update to save your new password.
Step 5 Click Return to the Menu or Log Off at the bottom of the page.
You can also change your PIN for accessing Cisco IP Phone Services, such as
Personal Address Book, Personal Fast Dials, and Cisco CallManager Extension
Mobility.
6-3
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Chapter 6 Customizing Your Phone on the Web
Customizing Your Cisco IP Phone on the Web
Procedure for Changing your PIN
Step 1 From the User Options main menu, select your phone or, if applicable, your
Cisco CallManager Extension Mobility device profile from the Select a device to
configure drop-down list.
Step 2 Click Change your PIN.
The Change Your Personal Identification Number (PIN) page appears.
Step 3 Fill in the fields as follows:
a. In the Current PIN text box, enter your current PIN.
b. In the New PIN text box, enter your new PIN.
c. In the Confirm New PIN text box, enter your new PIN again to confirm it.
Step 4 Click Update to save your new PIN.
Step 5 Click Return to the Menu or Log Off at the bottom of the page.
Customizing Your Cisco IP Phone on the Web
There are additional features and services that might be supported on your
Cisco IP Phone. You can customize them by accessing the User Options web
pages. See Table 6-1 on page 6-4 for a list of examples.
Note For a complete description of the features and services that are available and how
you can customize them on your Cisco IP Phone, refer to
Customizing Your Cisco IP Phone on the Web.
Additional Features and Services
Table 6-1 includes a sample list of additional features and services that might be
available on your Cisco IP Phone.
Before you can access some of these features and services, they must be assigned
by your system administrator. Check with your system administrator to determine
the services that are available to you.
Chapter 6 Customizing Your Phone on the Web
Customizing Your Cisco IP Phone on the Web
6-4
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Table 6-1 Additional Features and Services
Feature/Service... Explanation...
Call Forwarding Redirects your incoming calls to another number.
Speed Dial Provides quick access to frequently dialed numbers.
Abbreviated Dialing Extends speed dial functionality by using a dial entry index number
while your phone is on-hook. For information about using this
feature, see the Extending Speed Dial Functionality section on
page 2-10.
Cisco IP Phone Services Provides access to information services, such as weather, stock
quotes, and other services available at your company, using your
Cisco IP Phones LCD display.
Personal Address Book Allows you to look up address book entries and to dial a chosen
number by pressing a softkey on your phone. For information about
using this feature on your phone, see the Using a Personal Address
Book section on page 8-2.
Fast Dial Service Lets you assign Fast Dial codes to personal address book entries to
dial those codes in place of phone numbers. For information about
using this feature on your phone, see the Using the Fast Dial
Service section on page 8-4.
Message Waiting Indicator
Lamp Adjustments
Enables a change in the behavior policy of the message waiting
indicator light (or lamp) for each line appearance on your
Cisco IP Phone.
Default Language for Your
Phone and Profile
Allows you to change the default language in which information is
displayed on the Cisco IP Phones LCD screen and on the
Cisco CallManager User Options web pages.
CHAPTER
7-1
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
7
Using Your Voice Messaging System
Your phone administrator chooses the voice messaging system that your phone
uses. For information about how to use your voice messaging system, refer to the
documentation that came with your phone. For example, if your administrator
configured your phone system to work with Cisco Unity, refer to the Cisco Unity
documentation for information about accessing your voice messages.
See Table 7-1 on page 7-1 for specific information about using your voice
messaging system.
Table 7-1 Using Your Voice Messaging System
If you want to... Then...
Set up your voice messaging
system
Press the Messages button on your Cisco IP Phone and follow the
voice prompts. Your system administrator will provide you with a
default password. For security reasons, you should change your
default password as soon as possible.
Chapter 7 Using Your Voice Messaging System
7-2
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Recognize when you have a
voice message
Check your Cisco IP Phone for the following indicators:
The red light on your handsetThis indicator can vary,
depending on how the message waiting lamp is configured, but
it usually remains lit when you have a voice message. See the
Customizing Your Cisco IP Phone on the Web section on
page 6-3. Refer to Customizing Your Cisco IP Phone on the Web
for additional information.
A flashing envelope icon that is displayed next to the
appropriate line appearance on the LCD screen.
A text message that is displayed on the LCD screen.
Listen to a voice message Press the Messages button and follow the voice prompts.
Table 7-1 Using Your Voice Messaging System (continued)
If you want to... Then...
CHAPTER
8-1
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
8
Managing Your Phone Contacts
Your Cisco IP Phone might supply several different features to help you manage
your phone contacts: a personal address book, a Cisco IP phone synchronizer, the
Personal Address Book service, and the Fast Dial service.
Note These features are optional. Check with your system administrator to find out
which features are available to you.
The Personal Address Book allows you to store names and numbers of your
common contacts. From your Cisco IP Phone, you can use the Personal Address
Book service to look up entries, make a selection, and press a softkey to dial the
selected number.
With the Fast Dial service, you can assign index numbers (from 1 to 99) for quick
dialing from your Cisco IP Phone. You can assign index numbers either to
Personal Address Book entries or to directory entries that you add that do not
correspond to the address book. You can assign and remove the Fast Dial entries
from your phone or the Cisco IP Phone User Options application.
Note The exact names of the Personal Address Book and Fast Dial services might
vary, depending on how your system administrator configured these services.
With the Personal Directory synchronization tool, you can synchronize the
following address book entries stored on your computer with the
Cisco CallManager directory:
Microsoft Windows address book
Chapter 8 Managing Your Phone Contacts
Using a Personal Address Book
8-2
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Microsoft Outlook address book
Microsoft Outlook Express address book
This chapter covers the following topics:
Using a Personal Address Book, page 8-2
Using the Cisco IP Phone Address Book Synchronizer, page 8-4
Using the Fast Dial Service, page 8-4
Using a Personal Address Book
Before you can use a personal address book on your phone, you must be
subscribed to a personal address book service. See the Customizing Your Cisco
IP Phone on the Web section on page 6-3, and refer to
Customizing Your Cisco IP Phone on the Web for additional details.
Searching Personal Address Book Entries on Your Phone
Use the following procedure to find a personal address book entry.
Procedure
Step 1 Press the Services button.
The phone displays the services that have been configured for your phone.
Step 2 Use the Navigation button to highlight the option that corresponds to the My
Address Book service and press the Select softkey.
Tip The exact service name might vary, depending on how your system
administrator configured the service.
Step 3 Perform one of the following actions:
To display a specific name, enter the name using your phone keypad and press
the Submit softkey. All names that match your search criteria will display.
To display all your address book entries, press the Submit softkey.
8-3
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Chapter 8 Managing Your Phone Contacts
Using a Personal Address Book
Step 4 Using the Navigation button, highlight the entry that you want and press the
Select softkey.
Editing a Personal Address Book Entry on Your Phone
Use the following procedure to edit a Personal Address Book entry.
Procedure
Step 1 Find the entry that you want to edit, as described in the Editing a Personal
Address Book Entry on Your Phone section on page 8-3.
Step 2 Press the Edit softkey.
The phone displays the Personal Address Book information for that entry.
Step 3 Perform one of the following actions:
To edit the first name, last name, or nickname for this entry, press the Name
softkey.
To edit the home, work, or mobile numbers, press the Phone softkey.
Step 4 Make your changes and press the Submit softkey.
The phone displays a message that your change is successful.
Step 5 Press the OK softkey.
Dialing a Personal Address Book Entry
Use the following procedure to dial a Personal Address Book entry.
Procedure
Step 1 Find the entry that you want to dial, as described in the Editing a Personal
Address Book Entry on Your Phone section on page 8-3.
Chapter 8 Managing Your Phone Contacts
Using the Cisco IP Phone Address Book Synchronizer
8-4
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Step 2 Use the Navigation button to choose the directory number that you want to dial
and press the Dial softkey.
Using the Cisco IP Phone Address Book
Synchronizer
You can synchronize your Microsoft Outlook and/or your Outlook Express
address book entries with the directory in Cisco CallManager using the
Cisco IP Phone Address Book Synchronizer.
Note For detailed information about the Cisco IP Phone Address Book Synchronizer,
refer to Customizing Your Cisco IP Phone on the Web.
Using the Fast Dial Service
With the Fast Dial service, you can assign index numbers (from 1 to 99) to phone
numbers for quick dialing from your Cisco IP Phone.
To use Fast Dial, you must subscribe to the Fast Dial service and use either your
phone or the User Options web pages to assign Fast Dial numbers.
Creating a Fast Dial Entry for a Number in Your Personal Address
Book on Your Phone
Use the following procedure to create a Fast Dial entry for a number in your
Personal Address Book. For information about creating an entry for a directory
number that is not in your address book, see the Creating a Fast Dial Entry for a
Non-Address Book Directory Number on Your Phone section on page 8-5.
8-5
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Chapter 8 Managing Your Phone Contacts
Using the Fast Dial Service
Procedure
Step 1 Find the address book entry for which you want to create a Fast Dial, as described
in the Editing a Personal Address Book Entry on Your Phone section on
page 8-3.
Step 2 Use the Navigation button to highlight the appropriate entry and press the Select
softkey.
Step 3 Press the FastDial softkey.
Step 4 Use the Navigation button to highlight the directory number that you want to
assign to a Fast Dial index (home, work, or mobile) and press the Select softkey.
Step 5 Use the Navigation button to choose a fast-dial index and press the Select softkey.
A message displays that the Fast Dial entry has been created.
Step 6 Press the OK softkey.
Creating a Fast Dial Entry for a Non-Address Book Directory
Number on Your Phone
Use the following procedure to create a Fast Dial entry for a directory number that
is not in your Personal Address Book. For information on creating an entry for a
number in your address book, see the Creating a Fast Dial Entry for a Number in
Your Personal Address Book on Your Phone section on page 8-4.
Procedure
Step 1 From your Cisco IP Phone, press the services button.
The phone displays the services that have been configured for your phone.
Step 2 Use the Navigation button to highlight the option that corresponds to the My Fast
Dials service and press the Select softkey.
Tip Remember, the exact service name might vary, depending on how your
system administrator configured the service.
Chapter 8 Managing Your Phone Contacts
Using the Fast Dial Service
8-6
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Step 3 Press the Assign softkey.
A message displays a request that you choose an index to assign.
Step 4 Use the Navigation button to highlight a fast-dial index and press the Select
softkey.
Step 5 Enter a directory number and press the Submit softkey.
A message displays that the Fast Dial entry has been created.
Step 6 Press the OK softkey.
Removing a Fast Dial Entry on Your Phone
Use the following procedure to remove a Fast Dial entry.
Procedure
Step 1 From your Cisco IP Phone, press the Services button.
The phone displays the services that have been configured for your phone.
Step 2 Use the Navigation button to highlight the option that corresponds to the My Fast
Dials service and press the Select softkey.
Step 3 Press the Remove softkey.
A message prompts you to choose an index to remove.
Step 4 Use the Navigation button to highlight the index that you want to remove and
press the Select softkey.
A message shows that the entry has been removed.
Step 5 Click the OK softkey.
Dialing a Fast Dial Entry
Use the following procedure to dial a number using the Fast Dial service.
8-7
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Chapter 8 Managing Your Phone Contacts
Using the Fast Dial Service
Before You Begin
Before you can use the Fast Dial feature on your Cisco IP Phone, you must
subscribe to the Fast Dial service. For information about subscribing to services,
refer to Customizing Your Cisco IP Phone on the Web.
Procedure
Step 1 From your Cisco IP Phone, press the Services button.
The phone displays the services that have been configured for your phone.
Step 2 Use the Navigation button to highlight the option that corresponds to the My Fast
Dials service and press the Select softkey.
Tip Remember, the exact service name might vary, depending on how your
system administrator configured the service.
A screen displays your Fast Dial entries.
Step 3 Use the Navigation button to choose a fast dial number and press the Dial softkey.
Chapter 8 Managing Your Phone Contacts
Using the Fast Dial Service
8-8
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
CHAPTER
9-1
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
9
Logging In to Your Extension Using the
Cisco CallManager Extension
Mobility Feature
Your system administrator might provide you with a service called
Cisco CallManager Extension Mobility. This service allows you to associate your
phone number and user profile with any Cisco IP Phone. When you use your
Cisco CallManager Extension Mobility personal identification number (PIN) to
log in to a Cisco IP Phone, your assigned telephone number, and the settings that
you have established from the Cisco CallManager User Options web pages, are
associated with that phone.
Note For information about the User Options web pages, see Chapter 6, Customizing
Your Phone on the Web.
Cisco CallManager Extension Mobility is useful to you if you do not routinely
conduct business in the same office space every day.
Your system administrator will inform you whether this service is available to
you.
If you are logged out of a Cisco IP Phone that has the Cisco CallManager
Extension Mobility feature configured for it, you will not be able to make calls,
receive calls, or check voice messages from that phone until you log in. Also,
Cisco CallManager Extension Mobility might automatically log you out after a
certain amount of time. This time limit is established by your system
administrator. Therefore, we recommend that you log in to your phone at the
Chapter 9 Logging In to Your Extension Using the Cisco CallManager Extension Mobility Feature
Logging In to Cisco CallManager Extension Mobility
9-2
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
beginning of every day. If you hear a busy signal after pressing the Messages
button or any key on the touchtone key pad, then you must log in before using the
phone.
With Cisco CallManager Extension Mobility, you can be logged into only one
phone at a time. If you want to use another phone, you must log out of the first
phone.
Your Cisco CallManager Extension Mobility profile does not maintain ring type,
contrast settings, and volume settings; configure these settings directly on the
Cisco IP Phone.
This chapter covers the following topics:
Logging In to Cisco CallManager Extension Mobility, page 9-2
Logging Out of Cisco CallManager Extension Mobility, page 9-3
Changing Your Cisco CallManager Extension Mobility PIN, page 9-4
Logging In to Cisco CallManager Extension Mobility
To log in to Cisco CallManager Extension Mobility, perform the following steps.
Your system administrator will provide you with the necessary user ID and
personal identification number (PIN).
Tip We recommend that you log in to your phone at the beginning of the work day.
This practice ensures that your user device profile gets loaded on your phone. If
you make changes to your profile, the changes will apply wherever you log in.
Procedure
Step 1 Press the Services button on your Cisco IP Phone.
Step 2 From the Services menu, use the Navigation button to select the login option for
extension mobility. Then, press the Select softkey.
9-3
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Chapter 9 Logging In to Your Extension Using the Cisco CallManager Extension Mobility Feature
Logging Out of Cisco CallManager Extension Mobility
Note Your system administrator chooses the name for your particular
extension mobility service. These options might be displayed on the
Settings menu of your phone LCD screen as extension mobility
service, for example.
Step 3 Enter your user ID. For information on entering letters on your phone, see the
Entering Characters on Your LCD Screen section on page 1-12.
Step 4 Use the Navigation button to scroll down to the PIN prompt and enter your PIN.
Step 5 Press the Submit softkey.
The Cisco IP Phone to which you have logged in now adopts your user profile
information, including your speed-dial numbers and established services. The
phone also becomes associated with your phone number. If you log in while the
receiver is off-hook, the changes will not take effect until you hang up.
You might be prompted to select the device profile to use. Use the Navigation
button to scroll to the device and click the Select softkey.
Step 6 Press the Exit softkey to return to the previous screen.
Logging Out of Cisco CallManager Extension
Mobility
When you are ready to log out of Cisco CallManager Extension Mobility, follow
these steps.
Procedure
Step 1 Press the Services button on your phone.
Step 2 Use the Navigation button to select the logout option for Cisco CallManager
Extension Mobility.
Step 3 Press the Select softkey.
Chapter 9 Logging In to Your Extension Using the Cisco CallManager Extension Mobility Feature
Changing Your Cisco CallManager Extension Mobility PIN
9-4
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Step 4 The phone might display Do you want to log out <your UserID>? If it does,
select Yes.
Step 5 Press the Exit softkey to return to the previous screen.
Changing Your Cisco CallManager Extension
Mobility PIN
To change your Cisco CallManager Extension Mobility PIN, use the
Cisco CallManager User Options web pages:
Note Changing your PIN will affect any service that requires a PIN, such as Personal
Address Book and Personal Fast Dials. If you use these services and change your
PIN, you must update those services before you can use them.
Before You Begin
Log in to the User Options web page. For information on the User Options web
page and how to access it, see the Logging on to the User Options Web Pages
section on page 6-1.
Procedure
Step 1 From the User Options main menu, click Change your PIN.
Step 2 Enter your current PIN and a new PIN in the required fields, then click Update.
Step 3 When you are finished, click Return to the Menu or Log Off at the bottom of the
page.
CHAPTER
10-1
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
10
Troubleshooting Your Phone
This chapter contains procedures and troubleshooting information you might need
to diagnose problems with your phone or to help install your phone.
This chapter covers the following topics:
Tips for Cleaning Your Cisco IP Phone, page 10-1
Tips for General Troubleshooting on Your Cisco IP Phone, page 10-1
Diagnosing Problems, page 10-3
Tips for Cleaning Your Cisco IP Phone
Caring for your Cisco IP Phone is easy. To clean your phone, use a soft cloth,
when needed. Do not use any liquids or powders on your phone for cleaning or
other purposes. Using anything other than a soft cloth can contaminate your
phones components and cause failures.
Tips for General Troubleshooting on Your
Cisco IP Phone
If you encounter problems with your phone, use the tips provided in Table 10-1
on page 10-2 to help troubleshoot and resolve the problem.
Chapter 10 Troubleshooting Your Phone
Tips for General Troubleshooting on Your Cisco IP Phone
10-2
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Table 10-1 Cisco IP Phone General Troubleshooting Tips
Symptom to check... Action to take...
Proper signaling/dial tone on the
phone
To check that signaling is working properly on your phone, press the
Speaker button to answer a call. If you hear a dial tone and you can
answer a call, signaling is working properly
Handset cradle clip gets stuck or
interferes with usage of the
phone
The phones are designed with a reversible handset cradle clip. This
clip is used with the plastic tab protruding out when the phone is in
a vertical (wall-mounted) position. The position of the tab can
interfere with the handset as it is placed in the cradle.
If the phone remains in the on-hook position, you might
experience continued ringing when you try to answer a call or
a lack of dial tone when you try to place a call. To resolve this
problem, you might need to reverse the clip.
If the handset cradle clip is in the wall-mounted position and
your phone is placed on a desktop, slide the clip upward to
remove it. Rotate the clip 180 degrees and slide it back in so that
the tab is hidden.
If the hook switch remains in the up position, tapping on the
phone should free the switch. You can also try pushing, and
suddenly releasing, the off-hook button after the handset has
been picked.
For additional information about adjusting the handset, see the
Adjusting the Handset Rest section on page 1-13.
Hook switch contact
performance is degraded and
causes intermittent operation
The hook switch contacts on the phone use a wiping action to
self-clean the contacts. If your phone is not used on a regular basis,
dust and other airborne contaminants might degrade the contact
performance and result in intermittent operation. If you have
periods of limited phone usage, you can clean the contacts by
quickly pressing and releasing the hook switch a dozen times.
10-3
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Chapter 10 Troubleshooting Your Phone
Diagnosing Problems
Diagnosing Problems
The information in the following sections is necessary only if your administrator
asks you to perform one of the procedures.
Accessing Network Configuration Data
You might need to access network configuration data to help your system
administrator troubleshoot a problem that you are experiencing with your phone.
Only a system administrator or technician can alter this data.
Glare on the phones LCD screen The footstand on the phone is designed to allow adjustment for
several positions to eliminate glare on the LCD screen. Adjust your
phone for optimum LCD screen clarity. See the Connecting Your
Cisco IP Phone section on page 1-2.
False off-hook condition because
of phone positioning or cable
usage
When the phone is in the most vertical position, the phone
might be forced forward and the handset might not sit properly
in the cradle. This creates a false off-hook condition. We
recommend that you position the phone one notch from the
most vertical position to ensure that the handset is firmly
resting on the hook switch.
Check to make sure that the LAN cable connected to the phone
is positioned properly. The LAN cable should be positioned to
pass out of the side of the phone between the base and the
footstand. If you are using a different cable than the one that
was packaged with your phone, the cable might not fit under the
rear of the footstand. This can cause the phone to tilt forward
and force it off-hook. Using the correct size LAN cable will
eliminate this problem.
Table 10-1 Cisco IP Phone General Troubleshooting Tips (continued)
Symptom to check... Action to take...
Chapter 10 Troubleshooting Your Phone
Diagnosing Problems
10-4
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Follow these steps to access network configuration data.
Procedure
Step 1 Press the Settings button.
Step 2 From the Settings menu, use the Navigation button to select Network
Configuration.
Step 3 Press the Select softkey.
From here, you can use the Navigation button to view your Network
Configuration information, such as Host Name, Domain Name, IP Address, MAC
address, TFTP server, Boot Load ID, Serial Number, manufacturing installed
certificate (MIC), and locally significant certificate (LSC).
Accessing Model Information
You might need to access your phone model information to help your system
administrator troubleshoot a problem that you are experiencing with your phone.
Follow these steps to access phone model information.
Procedure
Step 1 Press the Settings button.
Step 2 From the Settings menu, use the Navigation button to select Model Information.
Step 3 Press the Select softkey.
From here, you can use the Navigation button to view your model information,
such as Model Number, MAC address, Application Load ID, Boot Load ID, Serial
Number, and phone security information.
10-5
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Chapter 10 Troubleshooting Your Phone
Diagnosing Problems
Accessing Status Data
Your network administrator or technician might want to access status information
to monitor the performance of your phone.
Follow these steps to access status data.
Procedure
Step 1 Press the Settings button.
Step 2 From the Settings menu, use the Navigation button to select Status.
Step 3 Press the Select softkey.
The Settings Status submenu appears.
Step 4 Use the Navigation button to select the item that you want to view and press the
Select softkey.
From here, you can view Status Messages, Network Statistics, Firmware Versions,
and Expansion Module Statistics for your phone.
Troubleshooting Cisco CallManager Extension Mobility
Use Table 10-2 on page 10-6 to troubleshoot error codes and messages displayed
on your Cisco IP Phone.
Chapter 10 Troubleshooting Your Phone
Diagnosing Problems
10-6
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Table 10-2 Troubleshooting Error Messages
Error Code or Message Recommended Action for Users
0, 2, 3, 6, 9, 12, 100, 101 When you try to log in to Cisco CallManager Extension Mobility, the
phone displays one of these error codes or error messages.
Provide your system administrator with the information displayed on the
phone.
HTTP error
Invalid host
No services configured
Requesting...
Device does not allow logon
Device profile unavailable
Authentication error After you enter your UserID and PIN, the phone displays
Authentication error.
The system does not recognize your User ID or your PIN. Perform these
steps:
1. Try to log in again to confirm that you did not make a mistake when
you entered your UserID and PIN.
2. If you receive the error message again, contact your system
administrator to check that you have the correct UserID and PIN.
System not enabled for login After you enter your UserID and PIN, the phone displays System not
enabled for login.
Ask your system administrator to enable the Cisco CallManager
Extension Mobility service.
User logged in elsewhere After you enter your UserID and PIN, the phone displays User Logged
in elsewhere.
You are still logged in to the last phone you used with
Cisco CallManager Extension Mobility. You can be logged in to only
one phone at a time.
Log yourself out of the phone where you are still logged in. (Or, contact
your system administrator to log you out.) Then, you can log in at the
phone that you want to use.
10-7
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Chapter 10 Troubleshooting Your Phone
Diagnosing Problems
Using the Quality Reporting Tool
Your administrator might temporarily configure your Cisco IP Phone with the
Quality Reporting Tool to troubleshoot problems with your phone calls. With the
Quality Reporting Tool, you can use the QRT softkey to submit information about
problem phone calls to your system administrator.
Depending on how your system administrator configured the Quality Reporting
Tool for your phone, you can use the QRT softkey in one of two ways:
To quickly report an audio problem with a current call, press the QRT
softkey.
Your phone will display: Audio quality data will be collected and logged.
After you press the QRT softkey, you might be presented with a list of phone
menu options to provide more details about the problem. Follow the
instructions on the phone to submit the quality report information.
Your phone will display: Your feedback has been logged.
In either scenario, press the Exit softkey to return to the previous screen.
The system routes the data or information you submitted to your system
administrator to troubleshoot problems with your phone calls.
Chapter 10 Troubleshooting Your Phone
Diagnosing Problems
10-8
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
A-1
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
APPENDIX
A
FAQ
This Frequently Asked Questions section contains the following information:
How do I access my voice messages?, page A-2
How do I set up speed-dial numbers?, page A-2
How do I set up softkeys for speed dialing?, page A-2
How do I access the User Options web page?, page A-3
How do I see a list of my missed calls?, page A-3
How do I put a call on hold without a hold button?, page A-3
How do I change the contrast on the phones LCD screen?, page A-3
How do I change the settings for my Cisco CallManager Extension Mobility
line?, page A-3
How do I forward calls?, page A-4
How do I directly transfer calls?, page A-4
How do I join multiple parties into one call?, page A-4
How can I see a list of participants in an ad hoc conference call?, page A-4
How do I add my line to a shared line call?, page A-5
How do I keep my call information private?, page A-5
How do I store frequently-called numbers?, page A-5
Ive used up all my speed-dial buttons, can I add more?, page A-6
What is the maximum number of speed-dial numbers that I can configure on
my phone?, page A-6
Appendix A FAQ
How do I access my voice messages?
A-2
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
How do I assign a phone service to a button on my Cisco IP Phone?, page A-6
If I cannot answer a call that I have forwarded to another number, will the call
get rerouted to my voice messaging system?, page A-7
How do I set priority levels for my calls?, page A-7
How can I send calls directly to a voice messaging system?, page A-7
Why dont I get a dial tone after dialing an access code?, page A-8
How do I trace a suspicious call?, page A-8
Where can I find tips about cleaning my Cisco IP Phone?, page A-8
Where can I find general troubleshooting tips for my Cisco IP Phone?,
page A-8
How do I access my voice messages?
You can access your voice messages using the Messages button on your phone.
For information about setting up and accessing your voice messages, see
Table 7-1 on page 7-1 in Chapter 7, Using Your Voice Messaging System.
How do I set up speed-dial numbers?
You add, modify, and delete speed-dial numbers on the User Options web page.
For information about setting up your speed-dial numbers, refer to Customizing
Your Cisco IP Phone on the Web.
How do I set up softkeys for speed dialing?
You can enhance your speed dial functionality by configuring and using
abbreviated dialing entry numbers. See the usage instructions in the Extending
Speed Dial Functionality section on page 2-10, and refer to Customizing Your
Cisco IP Phone on the Web for additional configuration details.
A-3
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Appendix A FAQ
How do I access the User Options web page?
How do I access the User Options web page?
The User Options web page allows you to configure and/or modify certain settings
for your phone (such as speed-dial numbers). For instructions on how to access
this web page, see the Logging on to the User Options Web Pages section on
page 6-1.
How do I see a list of my missed calls?
You can list the missed calls, placed calls, and received calls on your phone. For
more information, see the Viewing and Dialing from the Phone Logs section on
page 2-8.
How do I put a call on hold without a hold button?
Some of the features and functions on your phone are accessed through softkeys.
To put a call on hold, see the Using Mute and Hold section on page 2-9.
How do I change the contrast on the phones LCD
screen?
You can make it easier to read the text on your phones LCD screen by adjusting
the contrast. See the Changing the LCD Screen Contrast section on page 5-4.
How do I change the settings for my
Cisco CallManager Extension Mobility line?
You change the settings for your Cisco CallManager Extension Mobility line the
same way that you change them for a regular line. When you want to change any
settings that are in the User Options web page, make sure to select the device
Appendix A FAQ
How do I forward calls?
A-4
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
profile for your extension mobility extension. The Cisco CallManager
Extension Mobility device profile usually has identifying text in the name, such
as EM.
How do I forward calls?
You can forward calls to another extension, or to your voice messaging system,
either from your phone or from the User Options web page.
For more information, see the Forwarding Calls to Another Extension section
on page 3-6.
How do I directly transfer calls?
You can directly transfer two established calls into one call (without a
consultation transfer) by pressing the DirTrfr softkey. For more information, see
the Directly Transferring Your Calls section on page 3-2.
How do I join multiple parties into one call?
You can join all parties of connected calls into one call by pressing the Join
softkey. For more information, see the Selecting Participants to Join a
Conference Call section on page 4-3.
How can I see a list of participants in an ad hoc
conference call?
You can see a list of the names and directory numbers for participants in an ad hoc
conference call by pressing the ConfList softkey. For more information, see the
Viewing Participants in a Conference Call section on page 4-2.
A-5
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Appendix A FAQ
How do I add my line to a shared line call?
How do I add my line to a shared line call?
You can add your line to a call-in-progress on a shared line by pressing the Barge
or cBarge softkey. For more information, see the Adding Your Line to a Shared
Line Call section on page 4-4.
How do I keep my call information private?
You can keep your call information private on shared lines by using the Privacy
feature. This feature must be enabled by your system administrator.
For more information, see the Keeping Your Call Information Private section on
page 4-7.
How do I store frequently-called numbers?
You can store frequently-called numbers easily, using either the phone or the
User Options web page.
If you have the Personal Directory service available on your phone, you can enter
numbers using that service (see the Searching Personal Address Book Entries on
Your Phone section on page 8-2.)
You can also enter numbers into the Personal Address Book on the User Options
web page (refer to Customizing Your Cisco IP Phone on the Web.)
To dial these numbers quickly, you can set them up in the following ways:
Speed-dial numbers, which appear directly on your phone (see the
Customizing Your Cisco IP Phone on the Web section on page 6-3 and refer
to Customizing Your Cisco IP Phone on the Web for additional details.)
Abbreviated dialing, which uses dial entry index numbers comprising one or
two digits (used with the AbbrDial softkey). See the Extending Speed Dial
Functionality section on page 2-10 and refer to Customizing Your Cisco IP
Phone on the Web for additional details.
Fast Dial service, if the phone service is available to you. See the
Customizing Your Cisco IP Phone on the Web section on page 6-3 and refer
to Customizing Your Cisco IP Phone on the Web for additional details.
Appendix A FAQ
Ive used up all my speed-dial buttons, can I add more?
A-6
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Ive used up all my speed-dial buttons, can I add
more?
If you assigned numbers to all of the speed-dial buttons on your phone, there are
additional ways to store numbers for fast retrieval:
Add a Cisco IP Phone 7914 Expansion Module to your phone, and get an
additional 14 speed-dial buttons. Refer to the Cisco IP Phone 7914 Expansion
Module Phone Guide.
Use the Fast Dial service to store the remainder of your phone numbers. See
the Using the Fast Dial Service section on page 8-4, and refer to
Customizing Your Cisco IP Phone on the Web for additional details.
Use Abbreviated Dialing to quickly dial a number that you have configured.
See the Extending Speed Dial Functionality section on page 2-10 and refer
to Customizing Your Cisco IP Phone on the Web for additional details.
What is the maximum number of speed-dial numbers
that I can configure on my phone?
You can configure up to 99 speed dial and/or abbreviated dial entries from the
Cisco CallManager User Options web page. See the Customizing Your Cisco IP
Phone on the Web section on page 6-3 and refer to Customizing Your Cisco IP
Phone on the Web for additional details.
How do I assign a phone service to a button on my
Cisco IP Phone?
Your system administrator configures the Service URL button for your phone to
allow one-touch access to phone services, such as weather, stock quotes and other
services available to your company. Once configured, you can use the
Cisco CallManager User Options web page to modify your setting for the
available service(s) that you want to add to the phone. Refer to Customizing Your
Cisco IP Phone on the Web for additional details.
A-7
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Appendix A FAQ
If I cannot answer a call that I have forwarded to another number, will the call get rerouted to my voice messaging
If I cannot answer a call that I have forwarded to
another number, will the call get rerouted to my
voice messaging system?
Yesas long as the forwarded call is not picked up by a person or an answering
machine. Although call forwarding sends an incoming call intended for your
Cisco IP Phone to another number, your Cisco IP Phone does not relinquish the
forwarded call unless the call is answered (in other words, picked up by a person
or an answering machine). Your Cisco IP Phone considers a forwarded call
unanswered after a certain number of rings. Unanswered, forwarded calls are
redirected to your voice messaging system (if one is available).
How do I set priority levels for my calls?
You can set and see the priority levels for your calls by using the
Multilevel Precedence and Preemption feature. With this feature, authorized
parties can place priority calls and preempt lower priority calls. This feature must
be enabled by your system administrator.
For more information, see the Setting Up and Receiving Priority Calls section
on page 2-11.
How can I send calls directly to a voice messaging
system?
You can use call forwarding from your phone or from the User Options web page
to send calls directly to a voice messaging system without ringing your desk top
phone. Follow the procedure in the Forwarding Calls to Another Extension
section on page 3-6 and choose the Voice Messaging option.
You can also immediately redirect an incoming call to your voice messaging
system, or an outgoing call to the voice messaging system of the called party, by
using the Immediate Divert feature from your phone. See the Sending Calls to a
Voice Messaging System section on page 3-8.
Appendix A FAQ
Why dont I get a dial tone after dialing an access code?
A-8
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Why dont I get a dial tone after dialing an access
code?
If you use an access code, such as 9, to make external calls, you might not hear a
dial tone after you have dialed the access code. Continue dialing your call.
How do I trace a suspicious call?
You can use the Malicious Call Identification feature to trace a suspicious call that
you have received. This feature must be enabled by your system administrator.
For more information, see the Tracing Suspicious Calls section on page 2-10.
Where can I find tips about cleaning my
Cisco IP Phone?
You can find tips about how to care for your IP phone in the Tips for Cleaning
Your Cisco IP Phone section on page 10-1.
Where can I find general troubleshooting tips for my
Cisco IP Phone?
You can find general troubleshooting tips for your IP phone in the Tips for
General Troubleshooting on Your Cisco IP Phone section on page 10-1.
B-1
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
APPENDIX
B
Safety Notices
This appendix contains important safety infomation. Read the following safety
notices before installing or using your Cisco IP Phone.
These safety notices apply to phones in the Cisco IP Phone 7960G and 7940G
series.
Warning
This warning symbol means danger. You are in a situation that could cause
bodily injury. Before you work on any equipment, be aware of the hazards
involved with electrical circuitry and be familiar with standard practices for
preventing accidents.
Warning
Read the installation instructions before you connect the system to its power
source.
Warning
Ultimate disposal of this product should be handled according to all national
laws and regulations.
Warning
The plug-socket combination must be accessible at all times because it serves
as the main disconnecting device.
Appendix B Safety Notices
B-2
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Warning
Do not work on the system or connect or disconnect cables during periods of
lightning activity.
Warning
To avoid electric shock, do not connect safety extra low voltage (SELV) circuits
to telephone network voltage (TNV) circuits. LAN ports contain SELV circuits,
and WAN ports contain TNV circuits. Some LAN and WAN ports use RJ-45
connectors. Use caution when connecting cables.
The following warnings apply when you use the external power supply with the
Cisco IP Phone:
Warning
This product relies on the building's installation for short-circuit (over current)
protection. Ensure that a fuse or circuit breaker no larger than 120 VAC, 15A U.S.
(240 VAC, 10A international) is used on the phase conductors (all
current-carrying conductors).
Warning
The device is designed to work with TN power systems.
Using External Devices with Your Cisco IP Phone
The following information applies when you use external devices with the Cisco
IP Phone:
Cisco recommends the use of good quality external devices (speakers,
microphones, and headsets) that are screened against unwanted radio
frequency (RF) and audio frequency (AF) signals.
Depending on the quality of these devices and their proximity to other
devices such as mobile phones or two-way radios, some audio noise may
still occur. In these cases, Cisco recommends that you take one or more of
the following actions:
Move the external device away from the source of the RF or AF signals.
Route the external device cables away from the source of the RF or AF
signals.
Use screened cables for the external device, or use cables with a better
screen and connector.
B-3
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Appendix B Safety Notices
Shorten the length of the external device cable.
Apply ferrites or other such devices on the cables for the external
device.
Cisco cannot guarantee the performance of the system because Cisco has no
control over the quality of external devices, cables, and connectors. The
system will perform adequately when suitable devices are attached using
good quality cables and connectors.
The following warning applies for countries of the European Union when using
external devices attached to a Cisco IP Phone.
Caution In European Union countries, use only external speakers, microphones, and
headsets that are fully compliant with the EMC Directive [89/336/EC].
Caution Using a cell, mobile, or GSM phone, or two-way radio in close proximity to a
Cisco IP Phone might cause interference. For more information, refer to the
manufacturer's documentation of the interfering device.
Caution Use only a Cisco-approved power supply to power your Cisco IP Phone.
Appendix B Safety Notices
B-4
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
IN-1
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
INDEX
Symbols
? button
identifying
1-8
using 1-11
A
abbreviated dialing
customizing
6-4
using 2-10
about this book xi
ad hoc conference call 4-2
adjusting
LCD screen contrast
5-4
ringer 5-2
volume 5-1
answering calls 2-5
AutoAnswer, answering calls with 2-5
auto-registering your phone 1-10
B
barge
about
4-4
limitations 4-6
understanding shared lines 4-4
busy lines, using Cisco Call Back 2-6
C
cable connections on your phone 1-4
call park, and storing calls 3-4
call pickup
about
3-5
answering calls outside your group 3-6
answering calls within your group 3-5
cBarge 4-6
Cisco Call Back, about 2-6
Cisco CallManager Extension Mobility
about
9-1
changing your PIN 9-4
logging in 9-2
logging out 9-3
Cisco IP Phone
buttons
1-6
connecting 1-5
features 1-6
overview 1-1
using help 1-11
Index
IN-2
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
using softkeys 1-11
cleaning your phone 10-1
Conferee List 4-2
conference calls
ad hoc
4-2
joining a conference call 4-3
Meet-me 4-8
placing 4-1
viewing participants 4-2
conference modes
Barge
4-5
cBarge 4-5
types 4-5
connecting your phone 1-2
contacts
about
8-1
synchronizing 8-4
conventions, document xviii
D
directories
button, about
1-11
button, identifying 1-8
dialing numbers with 2-7
Direct Transfer
exceptions
3-2
using 3-2
using for a connected call and a call on
hold
3-3
using for two calls on hold 3-2
using for two selected calls from a connected
call
3-3
documentation
conventions
xviii
related xiii
E
ending calls 2-6
F
FAQ (Frequently Asked Questions) A-1
Fast Dial service
about
8-4
creating entries 8-4
placing calls with 8-6
removing entries 8-6
footstand
adjusting
1-6
identifying 1-8
forwarding
calls
3-6
canceling call forwarding 3-8
Frequently Asked Questions (FAQ) A-1
IN-3
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Index
G
group call pickup 3-6
H
handset rest, adjusting 1-13
handsets
about
1-8
adjusting volume 5-1
answering a call with 2-5
ending a call with 2-6
placing a call with 2-2
headset button, identifying 1-9
headsets
adjusting volume
5-1
answering a call with 2-5
ending calls with 2-6
ordering 1-15
placing a call with 2-3
using 1-15
help button
identifying
1-8
using 1-11
hold
putting calls on
2-9
resuming held calls 2-9
I
Immediate Divert
exceptions
3-8
status messages 3-9
using 3-8
using on an incoming call 3-8
using on an outgoing call 3-8
installing your phone 1-2
introduction 1-1
J
joining a conference call 4-3
K
keypad, identifying 1-9
L
LCD screen, identifying 1-8
line buttons, identifying 1-8
logging in
Cisco CallManager Extension Mobility
9-2
user options web pages 6-1
logging out, Cisco CallManager Extension
Mobility
9-3
Index
IN-4
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
M
Malicious Call Identification
identifying
2-10
tracing suspicious calls 2-10
using 2-10
Meet-me conferences
about
4-8
establishing 4-8
joining 4-9
messages button
about
1-10
identifying 1-9
message waiting indicator light 1-8
missed calls, viewing 2-8
multilevel call precedence and preemption
exceptions
2-13
messages 2-13
precedence calls 2-11
preempting calls 2-12
receiving 2-12
setting up 2-12
using 2-11
multiple lines
and placing calls
2-2
using hold with 2-9
mute button, identifying 1-8
P
personal address book
editing
8-3
placing a call with 8-3
searching 8-2
phone logs, about 2-8
PIN, changing for Cisco CallManager
Extension Mobility
9-4
placed calls, viewing 2-8
placing a call 2-2
power supply 1-6
priority calls
about
2-11
receiving 2-12
setting up 2-12
Privacy 4-7
R
received calls, viewing 2-8
redialing 2-3
redirecting calls 3-8
related documentation xiii
ringer
adjusting the volume
5-2
personalizing tones 5-2
IN-5
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
Index
S
services
button, about
1-10
button, identifying 1-9
settings button
about
1-10
identifying 1-8
shared lines
privacy
4-7
using 4-4
softkeys, about 1-9
speaker button, identifying 1-8
speakerphone
adjusting volume
5-1
answering a call with 2-5
ending calls with 2-6
placing a call with 2-3
using 1-14
speed dial
buttons, identifying
1-8
extended functionality 2-10
storing calls, using call park 3-4
synchronizing contacts 8-4
T
TAPS (Tool for Auto-Registered Phones
Support)
1-10
Tool for Auto-Registered Phone Support
(TAPS)
1-10
tracing suspicious calls 2-10
transferring calls
to another extension
3-1
using direct transfer 3-2
troubleshooting your phone 10-1
U
user options web pages
about
6-1
logging in 6-1
V
voice messaging
immediately sending calls
3-8
using 7-1
volume
adjusting ringer volume
5-2
adjusting volume of caller 5-1
button, identifying 1-9
W
warnings, translated xix
Index
IN-6
Cisco IP Phone 7960G and 7940G User Guide
OL-4637-01
101


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cisco 7960G at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cisco 7960G in the language / languages: English as an attachment in your email.

The manual is 4,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info