588920
3
Zoom out
Zoom in
Previous page
1/11
Next page
3
Congratulations on your purchase!
By purchasing the CICLOMASTER CM 8.3A you have acquired an electronic multifunctional sports
computer with an integrated altimeter function, with the highest level of precision and newest digital
transmission technology. The CM 8.3Ahas a state of-the-art electronics, is waterproof and convinces
through his high durability.
It’s special feature: Transmission from transmitter to device is implemented on a digital communication
level and this makes it extremely faultresistant. The CM 8.3A has a Two-in-One system. This means that
you can use it with 2 bikes and have the recorded values displayed separately for either bike or as a total.
In this case, the CM 8.3A automatically identifies immediately, after the first wheel rotations, which of
the two bikes is being used.
As another special features the CM 8.3A has an optional cadence measurement and an optional heart
rate measurement (for this you need separately available accessories ).
In order to use all functions of the CM 8.3A in the correct way, please read through this operating manual
carefully.
Content:
- CICLOMASTER CM 8.3A
- battery type CR 2032
- battery cap
- handlebar bracket
- speed-transmitter
- cable ties for mounting
- spoke magnet
1. General information
CM 8.3A has three modes: Bike 1, Bike 2, and Non-Bike mode.
To switch from one mode to another, simultaneously press the right and left buttons briefly (switching
is only possible if speed SPD = 0). In the Non-Bike mode, only bicycle independent functions will be
displayed.
CM 8.3A has an automatic energy save mode: If bike 1 or 2 does not receive any signals for more
than 5 minutes and you don’t press any button during this time, the display will be switched off (in the
non-bike mode it will be turned off after 15 hours.)
By pressing any button the display will be switched on again.
Because of the new digital transmission technique, the transmitters have to be initialized before using
CM 8.3A for the first time. We recommend initializing the transmitters before mounting the CM 8.3A on
the bike.
2. Installation
The handlebar bracket can be mounted on the handlebar or on the stem.
Picture A: Mounting is possible on handlebar (Position A-1) or stem (Position A-2).
Picture B: For using it on the stem (Position B), rotate upper part.
Remove the protective tape.
Place the handle bar and fasten it with the cable ties.
Picture C: Mount the transmitter with cable ties on the fork an cutt the ends
Picture D: Fix the magnet on a spoke so that it will face the mark on the transmitter. Adjust the magnet
position and fine tune the sensor if necessary (distance between transmitter and magnet max.
3 mm).
Picture E: Rotate the CM 8.3A to 45 degree left and install it into the bracket. Then rotate it 45 degrees
right to lock it. To unlock, rotate 45 degrees to the left.
A-1A
B
90ϒ
D
C
E
45ϒ
KLICK!
F
A-2
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ciclo CM 8.3 A Master at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ciclo CM 8.3 A Master in the language / languages: English as an attachment in your email.

The manual is 3,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Ciclo CM 8.3 A Master

Ciclo CM 8.3 A Master User Manual - German - 12 pages

Ciclo CM 8.3 A Master User Manual - Dutch - 11 pages

Ciclo CM 8.3 A Master User Manual - Danish - 38 pages

Ciclo CM 8.3 A Master User Manual - French - 11 pages

Ciclo CM 8.3 A Master User Manual - Italian - 12 pages

Ciclo CM 8.3 A Master User Manual - Spanish - 11 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info