588920
10
Zoom out
Zoom in
Previous page
1/11
Next page
10
their training. But how do you train to achieve those aims in the most
efficient possible manner? How do you find the right intensity of effort
during the training? CICLOInZone
®
is the optimum training ZONE for
effort, resistance and weight loss.
What does CICLOInZone
®
do?
It calculates the optimum training zone for effort, resistance and
weight loss. The values vary from person to person and they offer a
valid training support – always staying between 70 % and 85 % of the
maximum heart rate.
(+/- 5% of tolerance, taking into consideration the actual heart rate
when at rest and the level of training).
The question of burning fat is seen in the “correct” light with
CICLOInZone
®
on the basis of the personal data collected.
9. Battery change
CM 8.3A: First you should put CM 8.3A into the “Powerdown Mode”
(see chapter 5 Settings) Open battery cap with a coin (unscrew to the
left). Insert battery type CR2032 (please use battery with smooth minus-
pole) with plus-pole facing up. Close battery cap, being sure not to over
tighten. After inserting the battery the display will show normal mode.
(Speed-)Transmitter: Open battery cap at the top of the transmitter
with a coin (unscrew to the left), remove old battery and insert new 12
V battery, type 23A (with pluspole facing up). Close battery cap, being
sure not to over tighten.
(Battery change in the optional cadence transmitter works in the same
way.)
Please do not throw away battery in your normal garbage.
10. Trouble shooting
Faulty or no display
- check to see if battery is installed properly or replace battery (Attention:
removing battery will clear all settings and values in the CM 8.3A)
- press AC-button on the rear of the computer
Actual Speed not displayed
- transmitter hasn`t been initialized (see chapter 5)
- check to see if wheel-sensor is mounted properly
- check the position of the spoke magnet (max. 3 mm distance to wheel-
sensor)
- make sure CM 8.3A is mounted in bracket correctly
- check wheel circumference
- start transmitter search (press left button for 3 seconds)
Speed to high or to low
- check wheel circumference
- check to see if you are using miles or kilometers
Transmitters cannot be initialized
(initialization is very slow or “error” displayed)
- Tranmitter battery is discharged or transmitter is defect
- Transmitter has already been initialized for one of the bikes. If you still
want to initialize the transmitter for the current bike you must initialize
the transmitter again for the other bike, but without an active transmit-
ter. “Error” will be displayed. Now you can initialize it again with the
choosen bike.
Automatic search of the transmitter doesn’t start by moving
the bike.
- CM 8.3A is not correctly located in the handlebar bracked
- A transmitter has already been found (CM 8.3A displays SPD 0) e.g. if
you switch bikes. If you stay in the transmitting area of the first trans-
mitter CM 8.3A displays 0. If CM 8.3A is outside the transmitting area
it will display -“. With the next movement of the bike the transmitter
search will start again.
- transmitter hasn`t been initialized (see chapter 5)
No heart rate displayed or values displayed are incorrect or
unstable
- proof whether heart rate is switched on in setting mode
- Check transmitter belt (battery)
- Skin too dry or cold
- Distance between CM 8.3A and transmitter belt is too big (max. 5m)
- start manual transmitter search (press left button for 3 seconds)
Manual transmitter search doesn’t start
- no transmitter has been initialized
Cadence is not displayed or value incorrect or unstable
- Check whether switched on in setting mode
- Check sensor and magnet for correct installation
- start transmitter search (press left button for 3 seconds)
CM 8.3A is making noise
- its normal because of the automatic movement sensor
PC Recording doesn’t start
- storage is full, you have to delete recorded tours (with HACtronic
program or the reset function in settings of CM 8.3A see chapter 5;
Attention: the other values will be deleted also)
Wrong values displayed for the altitude
- Check home-altitude values (adjusting mode), you may have adjusted
wrong values
- Air pressure has changed, e.g. caused by changing weather conditions
(readjust current hight)
11. Guarantee
We offer a guarantee for 2 years from the date of purchase on the CM
8.3A. The guarantee is limited to material and processing faults. Broken
transmitters, or damages of wasted parts of CM 8.3A are excluded from
the guarantee.
The guarantee is valid only if the computer, with accessories, has been
handled and maintained carefully and according to operating instructions.
The guarantee will take place through changes of or repairing the defective
parts. The guarantee doens’t cover direct, indirect or subsequent damages
which are related to the product.
This guarantee doesn’t limit any rights of the consumer (considering rela-
tive national law) in respect to the dealer.
To return the CM 8.3A under conditions/terms of the guarantee, please
refer to your dealer, your local distributor or send the computer with the
proof of purchase (date) and all accessories and with sufficient postage
to:
CICLO SPORT SERVICE
K. W. Hochschorner GmbH
Konrad-Zuse-Bogen 8
D-82152 Krailling
E-Mail: ciclo-service@ciclosport.de
Please read through the operating manual again carefully before sen-
ding in the device and check the battery.
In case of valid guarantee claims, the repaired device or a replacement
device will be returned free of charge.
Repair:
If your CM 8.3A is sent in for repair (or battery change) or if a gua-
rantee claim is not valid, repairs up to EUR 19.- will be carried out
automatically.
In case of higher repair costs you will be notified. The repaired device
will be sent back COD.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ciclo CM 8.3 A Master at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ciclo CM 8.3 A Master in the language / languages: English as an attachment in your email.

The manual is 3,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Ciclo CM 8.3 A Master

Ciclo CM 8.3 A Master User Manual - German - 12 pages

Ciclo CM 8.3 A Master User Manual - Dutch - 11 pages

Ciclo CM 8.3 A Master User Manual - Danish - 38 pages

Ciclo CM 8.3 A Master User Manual - French - 11 pages

Ciclo CM 8.3 A Master User Manual - Italian - 12 pages

Ciclo CM 8.3 A Master User Manual - Spanish - 11 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info