Manual Christopeit WALKER (page 15 of 44) (English, German, Dutch, French)

602838

Zoom out

Zoom in

1/44

English

Assembly Instructions

Before beginning assembly, be sure to observe our recommendations

and safety instructions.

Step 1:

Installation of the left support (33) and the right support (24) on the

foot (23) with the screws M8x50 (58), the washers 8//16 (59) and the

cap nuts M8 (61).

1. Place the screws (58), the washers (59) and the nuts (61) accessibly

beside the foot (23).

2. Place the left support (33) on the foot and align so that the hole patterns

in the foot are aligned.

(Note: The transport rollers (21) pre-assembled in the foot (23) must point

backwards (opposite to the line of sight when standing on the machine

during training. Right and left are speciﬁ ed as viewed standing on the ma-

chine during training.)

3. Push on each screw (58) a washer (59) and push them through each

hole.

4. Put a washer (25) on the end of each screw (58) and screw on a nut

(61).

5. Proceed as described in 1. – 4. with the right support (24) on the right

hand side of the foot (23).

Step 2

Installation of cover (38) at main frame (1) and cable (25)

at base of Magnet (18).

1. Put the tension cable (25) into the receiver of the base frame (1) and

insert the end of tension cable (25) into the base of magnet (15). Secure

the position of the tension cable (25) by screwing the nut at the end of the

tension cable in the indicated arrow direction. (See ﬁ gure 1-3)

2. Screw the cover (38) at main frame (1) tightly, by using screws (47) and

washers (62).

Step 3:

Installation of the pre-assembled main frame unit (1) on the left (33)

and right (24) supports with the screws M8x50 (63), the washers 8//22

(64).

1. Place the screws (63), two washers (64) accessibly beside the foot (23).

2. Lay the main frame unit (1) between the supports (33) and (24) and align

so that the hole patterns in the main frame (1) and the supports (33+24)

are aligned. (Note: You should ask a second person to hold the main frame

unit (1) or support it with a suitable object to perform the following steps

of assembly.)

3. Place a washer (64) on each screw (63) and then push the screws

through the holes in the supports (24) and (33) and tighten the main frame

(1) ﬁ rmly.

4. Push the ends of the sensor cable (42) (projecting from the main frame(1))

and sensor wire for support (68) (from the left support (33)) together.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Christopeit WALKER in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,99 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Christopeit WALKER Manual

Product: