793222
24
Zoom out
Zoom in
Previous page
1/76
Next page
24
GB
1. Put the weight casing (41) with pre-assembled weight
casing support (42) into the holes of rear foot (2). Get the end
of opposite weight casings supports (42) and bending plates
(43) together and screw them tightly by using screw M6x16
(100), washer 6//12 (116) and self locking nut M6 (126) as
showed in gure „A“.
2. Put the L-plate (32) under the top cross beam (5) into
appropriate position and screw it tightly by using screw M8x65
(106), washer 8//16 (117) and self locking nut M8 (125) as
showed in gure „B“.
3. Connect the upper bending plate connection additionally at
L-plate (32) by using screw M6x20 (135), washer 6//12 (116)
and self locking nut M6 (126).
4. Then put the screw cap for M8 (132) onto the M8 nut.
Installation of weight casing (41) with supports (42+43) at
L-plate (32) and rear foot (2).
STEP 19
1. Pull cable 2 (28) through the big hole of support 2 (7) and
connect the end of cable 2 (28) at cable pulley holder 2 (6)
by using screw M10x25 (109), washer 10//20 (118) and self
locking nut M10 (124) as showed in gure „C“.
2. Put two cable roller unit as gure „A“ shows together with
screw M10x45 (110), washer (118) and self locking nut (124),
insert the cable 2 (28) and install these units at holder of front
foot (1) in a way that the cable pulley can roll easy.
3. Put a cable roller unit as gure „A“ shows together with
screw M10x45 (110), washer (118) and self locking nut (124),
insert the cable 2 (28) and connect this at twin cable pulley
holder (27) in a way that the cable pulley can roll easy.
4. Take cable 2 (28) and enlarge it with 8 links chain (53) and
two carbine hooks (55) and connect cable 2 (28) with cable
pulley holder 2 (6), which is pre-assembled at cable 1 (26).
(Note: To get a smooth sliding cable system, you may adjust
the cable system at 8 links chain (53) with carbine hooks (55)
through setting them into another position.)
5. Then put the screw caps for M10 (131) onto all M10 screw
heads and nuts.
1. Connect the weight casing support (42) and bending plate
(43) at appropriate position of weight casing (41) by using
screw M6x16 (100), washer 6//12 (116) and self locking nut
M 6 (126). Note, that the weight casing supports (42) and
bending plates (43) have to mount into the right position as
showed in Step 18 drawing.
Installation of cable 2 (28) with cable pulley units.
Installation of weight casing (41) with weight casing
support (42) and bending plate (43).
STEP 17
STEP 18
6
55
53
55
28
27
7
6
1
131124
118
84
83
84
118
110
131
A
131
136
118
28
118
124
131
C
28
AC
A
1980mm
Cable 2
126 116
116 100
A
1
5
B
A
106
117
5
126 116
116
135
32
117 125
132
B
43
43
126 116
116 100
41
42
42
41
43
43
B A
B
B
A
A
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Christopeit SP5000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Christopeit SP5000 in the language / languages: English, German, Dutch, French, Polish as an attachment in your email.

The manual is 6.81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Christopeit SP5000

Christopeit SP5000 Additional guide - German - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info