663906

Christopeit Runner Pro Magnetic - 9829 Manual

14
Zoom out
Zoom in
Previous page
1/60
Next page
14
Assembly Instructions
Before beginning assembly, be sure to observe our
recommendations and safety instructions.
Step 1:
Installation of the left support (5) and the right support (4) on the
foot (27) with the screws M8x50 (16), the washers 8//16 (25) and the
cap nuts M8 (26).
1. Place the screws (16), the washers (25) and the nuts (26) accessibly
beside the foot (27).
2. Place the left support (5) on the foot and align so that the hole patterns
in the foot are aligned.
(Note: The transport rollers (41) pre-assembled in the foot (27) must
point backwards (opposite to the line of sight when standing on the
machine during training. Right and left are specified as viewed standing
on the machine during training.)
3. Push one screw (16) through each hole.
4. Put a washer (25) on the end of each screw (16) and screw on a nut
(26).
5. Proceed as described in 1. – 4. with the right support (4) on the
right hand side of the foot (27).
Step 2:
Installation of the pre-assembled main frame unit (1) on the left (5)
and right (4) supports with the screws M10x85 (23), the washers 10/
/20 (29) and the cover caps (15).
1. Place the screws (23), two washers (29) and the cover caps (15)
accessibly beside the foot (27).
2. Lay the main frame unit (1) between the supports (4) and 85) and align
so that the hole patterns in the main frame and the supports are
aligned.
(Note: You should ask a second person to hold the main frame unit (1)
or support it with a suitable object to perform the following steps of
assembly.)
3. Place a washer (29) on each screw (23) and then push the screws
through the holes in the supports (4) and 85) and tighten firmly.
4. Push a cover cap (15) onto the ends of each screw (23).
5. For the next steps of assembly, please loosen the screws (20) and
remove the panelling (3).
Step 3:
Assembly of resistance setting with cable pull/control of supporting
pipe to right (9) on the base frame (1) and on the cable control receiver
(45).
1. Insert the rope control in the receiver of the base frame (1) and hand
the cable control in the cable control receiver (45). Secure the position
of the cable control (9) by rotating the nut at the end of the cable control
in the indicated arrow direction.
2. Engage the end of the cable (9) in the cable holder (45).
3. Replace the panelling (3) removed in step 2 and secure with the
screws (20).
55
55
5
2727
2727
27
2626
2626
26
2525
2525
25
1616
1616
16
1010
1010
10
44
44
4
1515
1515
15
2323
2323
23
2929
2929
29
2020
2020
20
55
55
5
33
33
3
44
44
4
2929
2929
29
2323
2323
23
1515
1515
15
11
11
1
2020
2020
20
44
44
4
55
55
5
11
11
1
2727
2727
27
99
99
9
11
11
1
4545
4545
45
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Christopeit Runner Pro Magnetic - 9829 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Christopeit Runner Pro Magnetic - 9829 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 1,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info