585794
16
Zoom out
Zoom in
Previous page
1/48
Next page
16
Assembly Instructions
Before beginning assembly, be sure to observe our recom-
mendations and safety instructions.
Step 1:
Installation of the left support (48L) and the right support (48R)
on the foot (2) with the screws M8x80 (60), screws M8x60 (63),
screws M14x90 (62), washers 8//16 (59), washers 14//22 (58)
and washers 8//20 (69).
1. Place the screws (60+62+63) and the washers (58+59+69) ac-
cessibly beside the foot (2).
2. Place the left support (48L) at the foot so that the hole patterns
in the foot are aligned. (Note: The transport rollers (34) pre-as-
sembled in the foot (2) must point backwards (opposite to the line
of sight when standing on the machine during training. Right and
left are specifi ed as viewed standing on the machine during trai-
ning.)
3. Push one screw (60+62) through each hole and tighten the left
support (48L) at foot (2) fi rmly.
4.Connect the plugs of computer cables (53) and proceed as de-
scribed in 1. – 4. with the right support (48R) on the right hand
side of the foot (2).
5. Screw the connection tube (47) at support left and right
(48L+48R) tightly, by using screw (63) and washer (69).
Step 2:
Installation of the handrail connection tube (55) with handle
bar (46) At support Left + right (48) with screws M8x15 (64) and
washers 8//16 (59).
1. Place on each screw (64) one washer (59) and put them acces-
sibly beside the foot (2).
2. Put the plugs of computer cable (53) and hand pulse cable (54)
together.
3. Place the handle bars (46) with handrail connection tube (55)
onto the ends of support left and right (48L+48R) and tighten them
rmly by using the screws (64) with washer (57). (Observe that the
cable won’t squeeze.)
Step 3:
Installation of the base of computer (50) at handrail connec-
tion tube (55) with the screws M8x15 (64) and curved washers
8//20 (57).
1. Place on each screw (64) one washer (57) and put them acces-
sibly in front of the foot (2).
2. Place the base of computer (50) against the handrail connection
tube (55) and tight it fi rmly by using the screws (64) with washer
(57).
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Christopeit RUNNER PRO I loopband at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Christopeit RUNNER PRO I loopband in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info