793219

Christopeit POWER XL 1582 Manual

18
Zoom out
Zoom in
Previous page
1/56
Next page
18
Step 5:
Installation of the leg curler (10), the round pad holders (19) and the
round pads (20) on the front foot (8) with the shaft piece (44) and the
Allen screw (55).
1. Insert the leg curler in the holder of the foot (8). Align the holes in the
holder and the sliding bearings. Push the shaft piece (44) through
from one side. From the opposite side, screw the screw (45) into the
threaded
hole of the shaft piece and tighten firmly.
(Note: After installation, the holder of the foot (8) must not be bent and
the leg curler must move easily.)
2. Push the two round padding holders (19) centrally into the correspon-
ding holes of the leg curler (10). Push on a round pad (20) from each
side.
3. Finally, push a spring circlip 1 (27) on the bar bell weight holders of the
leg curler (10).
Step 4:
Installation of the butterfly arms (5) with round pad holder 1 (4) at the
rear feet (1) with the hexagonal screws (43), washers (52), spacer nut
(37), and handgrip nut (65).
1. Place the parts named above near the feet (1). Insert two sliding
bearings (25) in the middle of the butterfly arm (5). Put a washer (52)
on a screw (43), push the screw through the bearings and screw on a
nut (37) from the back.
(Note: Tighten the nut (37) only sufficiently to allow the screw (38) to
be easily turned.)
2. Push the end of screw (43) through the corresponding hole in the right
foot (1). Put on a washer (52), screw on a the handgrip nut (65) and
tighten firmly.
(Note: The butterfly arm (5) must move easily after installation.)
3. Insert the round pad holder 1 (4) into the butterfly arm (5) and push
one round pad (20) to fix it.
4. Install the second butterfly arm (5) and one round pad holder 1 (4) at
the other side on rear foot (1) as described in 1. - 3. The distance of
round pads (20) is adjustable by using another hole for fix them.
5. Finally, push a spring circlip 1 (27) on the bar bell weight holders of the
butterfly arms.
… 18 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Christopeit POWER XL 1582 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Christopeit POWER XL 1582 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2.63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info