Manual Christopeit HT 3 (page 15 of 48) (English, German, Dutch, French)

582515

Zoom out

Zoom in

1/48

English

Assembly Instructions

Before beginning assembly, be sure to observe our recommendations

and safety instruction. Remove all the part of your cycle from the carton

and place them on the ﬂoor carefully. Some parts are pre-assembled.

Assembly time: 30 - 40 min.

Step 1:

Attach the stabilizer (14+41).

1. Attach the front stabilizer (14) assembled with 2 front cross bar caps (13)

to main frame (32), using 2 bolts M8x55 (17), 2 washers (16), 2 spring

washers (76) and 2 cap nuts (15). The transportation wheel of foot-caps

(13) need front direction for use.

2. Attach the rear stabilizer (41) assembled with 2 rear cross bar caps (40)

and 2 height adjustable screws (42) to main frame (32), using 2 bolts

M8x55 (17), 2 washers (16), 2 spring washers (76) and 2 cap nuts (15).

(For uneven ﬂoor you can adjust the height with screw (42) and secure

position with nut (43).)

Step 2:

Attach the pedals (67L+67R).

1. Attach the pedal straps to the pedals (67R/67L).

(Note: The end with many adjustable holes must be set outwards.)

2. The pedals (67R/67L) are marked with „R“ & „L“

Note: Right and Left are speciﬁed as viewed seated on the machine

during training. Connect each pedal (67R/67L) to the matching crank

arm (66L+66R)

(Note: The right pedal „R“ should be threaded on clockwise. The left

pedal „L“ should be threaded on counter-clockwise.)

Step 3:

Installation of saddle (44) at saddle support (69) by using saddle slide

(75).

1. Push the saddle (44) with saddle bracket into the movable saddle slide

(75) and tight it up with washer (74) and nut (52).

2. Place the movable seat post (75) into the holder of saddle post (69), set

it at the desired horizontally position and tighten it by washer (71) and

movable seat knob (70).

3. Insert the saddle support (69) into the provided holder of the main frame

(32) and secure at the desired position by screwing in the rapid action

lock (60).

(Note: To screw in the rapid-action lock (60), the threaded hole in the

main frame (32) and one of the holes in the saddle support (69) must be

aligned. Furthermore, ensure that the saddle support (69) is not pulled

out of the main frame beyond the marked maximum Position. The setting

of the saddle post can be adjusted as desired later. For this, the rapid

action catch (60) must be loosened by only a few revolutions, the cap

of the lock must be pulled away and the saddle adjusted. Then secure

the new setting by tightening the rapid action catch.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Christopeit HT 3 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,51 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Christopeit HT 3 Manual

Product: