656850
22
Zoom out
Zoom in
Previous page
1/68
Next page
22
Step 3:
Assembly of the pedal tubes (9) and connection tubes (5).
1. Put the left pedal tube (9L) at the left connection tube (5L) and
adjust the holes in the tubes so that they are aligned. Push the
bolt M8x30 (22) through the holes and tighten the pedal tube
(9L) at connection tube (5L) with washer 8//16 (33) and nut (38)
firmly.
2. Place the preassembled unit of the left pedal tube (9L) and left
connection tube (5L) at the left hand side of the main frame (1).
(Note: Right and Left is specified as viewed standing on the
machine during training.) Put one wave washer 21//25 (36) and
the left connecting tube (5L) onto the left holder of support (2).
Put on the screw M8x20 (16) a spring washer (27) and a washer
8//32 (31) and tighten it firmly.
3. Put the left pedal tube (9L) onto the pedal tube support (7) and
adjust the holes in the tubes so that they are aligned. Push the
bolt M12x125 (44) through the holes and tighten the left pedal
tube (9L) at pedal tube support (7) with washers 12//24 (45) and
nut (46) firmly. Then put a screw cap for M12 (68) onto the nut
(46).
4. Put one pedal (65) onto the left pedal tube (9L). Adjust the holes
in the parts so that they are aligned. Push the screws M6x15
(23) from above through the holes and tighten firmly.
Step 4:
Assembly of pulse grip (11) and handgrips (6) at connection
tubes (5).
1. Put the handgrips (6L+6R) onto the connection tubes (5L+5R)
and adjust the holes in the tubes so that they are aligned. (Note:
the handgrips must be aligned after assembly so that the upper
ends are inclined outwards (away from the support (2)).
2. Push the bolt M8x16 (17) through the holes and tighten the
handgrips (6) with curved washers 8//20 (35) and spring washer
(27) firmly.
3. Place the pulse grip (11) to the support (2) and push the pulse
cable (59) through the hole of support (2) into inner top position.
Put the pulse grip (11) against the support (2) so that the holes
are aligned. Push a spring washer (27) and a washer (35) onto
each screw (17) and push them through the holes and tighten
the pulse grip (11) firmly.
5. Install the right pedal tube (9R) incl. all additionally required parts
on the right hand side of the machine as described in 1.– 4.
6. Place the caster onto the slide ways and turn the construction
by hand 3-4 times and then tighten the screws (17) of support
(22) as mentioned in Step 2 firmly. Finally push the support
cover into the right position.
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Christopeit FXM 2 - 1621 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Christopeit FXM 2 - 1621 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 3,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info