793190

Christopeit EMT 2200 Manual

21
Zoom out
Zoom in
Previous page
1/28
Next page
21
GB

The whole set of heart rate detector include 2 sensors each side. Each
sensor has 2 pieces of metal parts. The correct way to get detected is
to gently hold both metal parts each hand. With the good signals pi-
cked up by the computer, the heart mark in the HEART RATE Display
shall ash. Somemes the heart rate value is not useable, based on
wet hands or any other contact problems during exercising. If you need
high accuracy heart rate value you have to use an external heart rate
measurement with a pulse belt.

For pulse measurement, the pulse measuring unit 9309 must be in pla-
ce. The use of the pulse measuring unit makes it possible for you to
accurately monitor your own training programme by exact, real-me
measurement of your heart rate. The installaon of the system is very
simple and easily done.
The pulse measuring unit was developed especially for use with this
machine. The user puts on the unit and the transmier of the unit re-
gisters the ECG signals of the heart. The transmier amplies the ECG
signals and transmits them in the form of radio signals to the receiver
installed in the computer.
The transmier switches on automacally when the pulse measuring
unit is put on and the rear of the pulse measuring unit have made con-
tact with the breast. Any kind of normal training clothes may be worn
over the pulse measuring unit. The receiver installed in the computer
receives the signals from the transmier and transfers these in the
form of electrical impulses to the computer. The computer processes
the signals and displays them as pulse beats per minute on the display.
To aain an opmum performance of the pulse measuring unit, the
machine should be set up for training in such a manner that it is as far
as possible from all high-voltage power lines, electric motors and other
sources which can cause interference. Adjust the strap to your chest
measurement and put on the enre unit as depicted in the illustraon.
Ensure that the strap is not too loose and that the transmier is loca-
ted at the centre of your chest. The unit and thereby the pulse measu-
ring system is then installed and ready for use.
Clean the pulse measuring unit aer each training session with a cloth
moistened with a soap soluon and then with a cloth moistened with
pure water. This prevents the accumulaon of sweat which could lead
to inaccurate measurements.
If you noce during training that the values which must be displayed by
the computers appear irregularly or the symbol “P” appears in the dis-
play, conduct the following check procedure:
 Check that the strap is not too loose and/or has slipped too far dow-
nwards.
 Check whether the Christopeit-sport Brand on the transmier of the
pulse measuring unit is posioned correctly and is legible to a person
looking at the person in training.
 Ensure that the computer is switched on.
Moisten the part of the strap neat the transmier and which comes
into contact with the skin lightly with water to improve the transmis-
sion.
 Check whether the baery in the transmier is spent and change
this if necessary.
Remove and replace the baeries.




 Heart rate monitoring system may be inaccurate. Over
exercise may result in injury or death. If you feel faint stop exercising
immediately.

It is a funcon to check the condion of pulse recovery that is scaled
from 1.0 to 6.0 while 1.0 means the best and 6.0 means the worst and
the increment is 0.1. In order to get rated correctly, users must test it
right aer the workout nished by pressing „TEST“ key and then stop
exercising. Aer the key is pressed, please also apply the heart rate de-
tector appropriately. The test will last for 1 minute and the result will
show in the display.
RPM and Power in Wa of Level 1 - Level 24 for EMT 2200
Art.-Nr. 2098

The power consumpons (Wa) are adjusted by measuring the dri-
ving speed (min-1) of axle and the braking torque (Nm).
Your equipment was tested to fulll the requirements of its accuracy
classicaon before shipment, If you have doubts about the accuracy,
please contactwith your local retailer or send it to accredited test labo-
ratory to ensure or calibrate it.
(Please note that a deviaon tolerance as noted on page 15, is permis-
sible.)


Level 20RPM
WAT T
30RPM
WAT T
40RPM
WAT T
50RPM
WAT T
60RPM
WAT T
70RPM
WAT T
80RPM
WAT T
18 14 23 33 43 58 73
2 9 16 27 39 52 69 86
310 19 31 45 61 81 100
411 22 36 52 70 93 115
5 12 25 40 59 80 106 131
6 13 27 45 68 90 119 147
7 14 29 49 75 100 132 163
8 16 32 54 82 110 145 180
917 35 59 89 120 158 196
10 18 38 63 95 130 171 212
11 19 41 68 102 140 184 228
12 21 44 74 110 150 198 245
13 23 47 78 117 160 211 262
14 24 49 82 124 170 224 279
15 25 51 86 131 180 238 296
16 26 54 90 138 190 251 313
17 27 57 95 146 200 265 330
18 28 59 100 153 210 278 346
19 29 62 105 160 220 291 362
20 31 65 110 167 230 304 378
21 32 67 115 174 240 317 394
22 33 70 119 181 250 330 410
23 34 73 123 189 260 344 426
24 36 76 128 197 270 358 443

During body fat test, it will display Err2 if hand pulse sensors get no-
input.
According to test result, 10 seconds have no operaon or operaon
arbitrarily key, will get into system recommendaon to toughen pro-
gram.
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Christopeit EMT 2200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Christopeit EMT 2200 in the language / languages: English, German as an attachment in your email.

The manual is 3.72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info