793034
18
Zoom out
Zoom in
Previous page
1/32
Next page
18
GB

Remove all the separate parts from the packaging, lay
them on the oor and check that all are there on the
basis of the assembling steps. Please note that a num-
ber of parts have been connected directly to the main
frame and preassembled. In addion, there are seve-
ral other individual parts that have been aached to
separate units. This will make it easier and quicker for
you to assemble the equipment. Assembly me ap-
prox. 60min.


Aach the front foot (45) with preassembled trans-
portaon roller (44+46) to the main frame (40).
Do this with the two screws M8x55 (41), washers
8//16 (28) and self-locking nuts M8 (43).
Aach the rear foot (55) with preassembled height
adjustable screw (57) to the main frame (40). Do
this with the two screws (41), washers (28) and self
locking nuts (43). Aer assembly has been completed,
you can compensate for minor irregularies in the
oor by turning the foot screw (57). The equipment
should be set up that the equipment does not move
of its own accord during a training session.

       -

Place screws M8x16 (32), washers 8//16 (28), cur-
ved washers 8//19 (33) and spring washers for M8
(27) accessibly beside the front part of the main
frame (40).
Place the lower end of the support (8) against the
main frame (40) and plug the ends of the two com-
puter cable harnesses (2+39) projecng from (8+40)
together. (Note: The computer cable harness (2)
projecng from the support (8) must not slide into
the tube, as it is required for later steps of installa-
on.) When joining the tubes, ensure that the cable
connecon will not trapped.
 Put one spring washer (27) and one washer (28)
or curved washer (33) on each screw (32). Push the
screws (32) through the holes in the support (8),
screw into the threaded holes of the main frame (40)
and ghten rmly.



 Put the le footrest holder (103) at the pedal crank
(91) on le hand side and ghten the footrest holder
(103) with washers 8//22 (14), spring washer for M8
(27) and screw M8x20 (99) rmly. Put the screw cover
(98) onto the footrest holder (103).
2. Push the connecon tube cover (31) onto le con-
necon tube (34) into intended posion and ghten
with screws M5x12 (5).
 Install the right footrest holder (100) incl. all
addionally required parts on the right hand side of
the machine as described in 1. – 2.
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Christopeit CXT 7200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Christopeit CXT 7200 in the language / languages: English, German as an attachment in your email.

The manual is 4.3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info