582716
15
Zoom out
Zoom in
Previous page
1/48
Next page
15
English
Step 2:
Attach the pedal tube (6) and the swing tubes (4).
1. Remove the screws (57), wave washer (10), spring washers (52) and
D-shape washers (56) from long axle (12) and push the long axle (12)
centered into the holder of main frame (1). Put on one side the wave
washer (10) onto one axle (12).
2. Place the swing tube right (4R) on the right hand side of the main frame
(1) onto the end of long axle (12). (Note: Right is specified as viewed
standing on the machine during training.) Put the D-shape washer (56) in
position and secure swing tube right (4R) by using screw (57) and spring
washer (52).
3. Screw the right pedal tube (6R) at the pedal crank (10) with axle screw
right (41R) tightly and secure position with spring washer (51) and right
nut (48R) firmly. Then put the screw caps (59+60) onto the front and rear
connection pointsof pedal tube right (6R).
(Note: The screws (41L+R) are marked with “L” for left and “R” for right.
Please use appropriate nut for left and right screw. On right side the axle
screw and nut have to screw clock wise.)
4. Install the left pedal tube (6L) and swing tube (4L) incl. all additionally
required parts on the left hand side of the machine as described in 2. 3.
(Note: The screw direction on left side for axle screw and nut is anti-clock
wise.)
Assembly Instructions
Remove all the separate parts from the packaging, lay them on the
floor and check roughly that all are there on the base of the assembly
steps. Please note that a number of parts have been connected directly
to the main frame and preassembled. In addition, there are several other
individual parts that have been attached to separate units. This will make
it easier and quicker for you to assemble the equipment.
Assembly time: 30 - 40 min.
Step 1:
Attach the stabilizer (2+3) at main frame (1).
1. Attach the front foot (2) with the preassembled transport rollers to the
main frame (1). Do this with the two screws M8x50 (37) curved washers
8//20 (46) and cap nuts (47).
2. Attach the rear foot (3) to the main frame (1). Do this with the two screws
M8x50 (37), curved washers 8//20 (46) and cap nuts (47).
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Christopeit CT 1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Christopeit CT 1 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Christopeit CT 1

Christopeit CT 1 User Manual - Dutch - 11 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info