793027
15
Zoom out
Zoom in
Previous page
1/24
Next page
15
GB
 Push the handgrip bars (5R) onto the connecng tubes (25R) and adjust
the holes in the tubes so that they are aligned. ( the handgrip bars must
be aligned aer assembly so that the upper ends are inclined outwards (away
from the support (30)).
 Push the screws (33) through the holes and ghten the handgrip bars (5)
with curved washers (31) and spring washer (32) rmly.
 Put the footrest holder (44R) at the connecng tube (25R) and adjust the
holes in the tubes so that they are aligned.
 Push the screw M8x78 (23) through the holes and ghten the footrest
holder (44R) at connecon tube (25R) with washers (27) and nut (26) rmly.
(This connecon point has to move easily. So please don’t ghten the screw
too much.)
 Place the preassembled unit of the right footrest holder (44R) and con-
necng tube (25R) at the right hand side of the main frame (40). ( Right
is specied as viewed standing on the machine during training.)


 Place screws M8x20 (33), curved washers (31) and spring washers
(32) accessibly beside the front part of the main frame (40).
 Place the lower end of the support (30) against the main frame
(40) and push the rubber ring (100) and support cover (101) onto the
support (30).
 Plug the ends of the two computer cables (34-38) projecng from
(30+40) together. ( The connecon cable (34) projecng from
the support (30) must not slide into the tube, as it is required for later
steps of installaon.) When joining the tubes, ensure that the cable
connecon will not trapped.
 Connect the middle secon tension cable (39) to the bracket of
lower secon cable tension (35) (See gure A1-A3). Before this step
of the installaon, it is advisable to adjust the resistance seng to the
hardest stage 10, at which the cable extends furthest from the sheath.
Put the lowest part of cable (39) into the small hook (gure A1). Pull it
unl the small hook get in higher posion (A2) and then insert the ca-
ble (39) onto the bracket (35) (gure A3).
 Put one spring washer (32) and one curved washer (31) on each
screw (33). Push the screws (33) through the holes in the support (30),
screw into the threaded holes of the main frame (40) and ghten light-
ly.
 Push the plasc cover (101) and rubber ring (100) into the right
posion to cover the connecon point.



 Push the grip axle (19) into the middle
posion at handlebar support (30) and put
one wave washer (20) and the connecng
tube (25R) onto the axles’ end (19). Put on
the hex screw M8x20 (12) a spring washer
(32) and a washer 8//32 (22) and ghten it
rmly.
 Put the foot pedal holder (44R) at the
pedal crank (97) and ghten them with steel
tube (52), washer 8//20 (49), spring washer
(32) and screw M8x20 (48) rmly.
 Install the le footrest holder (44L) incl.
all addionally required parts on the le
hand side of the machine as described in 1.
– 7.
 Put the plugs of pulse cables (10) into
the plugs from pulse connecon cables (16)
and aach the screw caps (11) onto screws
(12).
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Christopeit CRT 7100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Christopeit CRT 7100 in the language / languages: English, German as an attachment in your email.

The manual is 2.92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info