Manual Christopeit CPS2 (page 14 of 48) (English, German, Dutch, French, Italian)

662743

Zoom out

Zoom in

1/48

Assembly Instructions

Before beginning assembly, be sure to observe our recommendations

and safety instructions.

Step 1:

Install of the front footbar (21) and the rear footbar (15) on the main

frame (1) with the carriage bolts M8x60 (17), the washers 8//20 /19),

the spring washers for M8 (72) and the cap nuts M8 (18).

1. Place screws (17) and two each washers (19), spring washers (72)

and nuts (18) accessibly beside the front and rear parts of the main

frame (1).

2. Insert the footbars (21) + (15) in the holder of the main frame (1) and

adjust so that the hole patterns of the holders and the footbars (21) +

(15) are aligned.

3. Push one screw (17) through each hole.

4. Fit the screw ends of (17) with one washer (19) and one spring washer

(72) each and fasten with a nut (18).

(Note: If the machine is placed for training on an uneven floor, this can

be compensated at any tome by turning the eccentric caps (16).

Step 2:

Installation of the right pedals (13) and the left pedals (14) on the pedal

crank.

1. The pedals are marked “R” for right and “L” for left.

2. Screw the right pedal (13) into the threaded hole on the right hand side

of the pedal crank (9) and tighten firmly.

(Note: Right and left are specified as viewed seated on the machine

during training. It must also be observed that the threaded part of the

right pedal must be screwed clockwise into the threaded hole of the

pedal crank.)

3. Screw the left pedal (14) into the threaded hole on the left hand side of

the pedal crank (9) and tighten firmly.

(Note: The threaded part of the left pedal must be screwed

anticlockwise into the threaded hole of the pedal crank.)

Step 3:

Installation of the saddle (52) on the saddle support (49) with the wash-

ers 8//20 mm (51) and the self-locking nuts M8 (50).

1. Place the saddle (52) with the seat surface downwards.

2. Place the retaining plate of the saddle support (49) on the upwards

pointing bottom of the saddle (52). The threaded pieces on the bottom

of the saddle must project through the corresponding holes in the

retaining plate of the saddle support (49).

3. Place washers (51) on the threaded pieces, screw on nuts (51) and

tighten firmly.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Christopeit CPS2 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 1,09 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Christopeit CPS2 Manual

Product: