Manual Christopeit CL2 (page 18 of 65) (English, German, Dutch, French, Polish)

793198

Zoom out

Zoom in

1/65

Step 3:

Installation of saddle (7) and saddle support (6).

1. Place the saddle (7) with the seat surface downwards.

2. Place the retaining plate of the saddle support (6) on the upwards

pointing bottom of the saddle (7). The threaded pieces on the

bottom of the saddle must project through the corresponding

holes in the retaining plate of the saddle support (6).

3. Place washers (33) on the threaded pieces, screw on nuts (34)

and tighten rmly.

4. Insert the saddle support (6) into the provided holder of the main

frame (1) and secure at the desired position by screwing in the

saddle support screw (31).

(Note: To screw in the saddle support screw (31), the threaded

hole in the main frame (1) and one of the holes in the saddle

support (6) must be aligned. Furthermore, ensure that the saddle

support (6) is not pulled out of the main frame beyond the marked

maximum adjustment position. The setting of the saddle support

can be adjust as desired later.)

Step 4:

Installation of handlebar support (4) at main frame (1).

1. Place screws (19), spring washer (25) and washers (35)

accessibly beside the front part of the main frame (1).

2. Place the lower end of the support (4) against the main frame (1)

and plug the ends of the two computer cables (17+18) projecting

from (1) and (4) together.

(Note: The computer cable harness (18) projecting from the

support (4) must not slide into the tube, as it is required for later

steps of installation. When joining the tubes, ensure that the cable

connection will not trapped.)

3. Connect the cable of tension control (20) to the bracket of lower

section cable tension (16) (See gure A1-3). Before this step of

the installation, it is advisable to adjust the resistance setting to

the highest stage, at which the cable extends furthest from the

sheath. Put the lowest part of cable (20) into the small hook (gure

A1) of tension cable (16). Pull it (gure A2) until the small hook

get in higher position and then insert the outer cable (20) onto

the bracket (16) (gure A3).

4. Push the handlebar support (4) onto the main frame (1) and put

one spring washer (25) and one washer (35) on each screw (19).

Push the screws (19) through the holes in the support (4), screw

into the threaded holes of the main frame (1) and tighten rmly.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Christopeit CL2 in the language / languages: English, German, Dutch, French, Polish as an attachment in your email.

The manual is 2.56 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Christopeit CL2 Manual

Product: