793198

Christopeit CL2 Manual

17
Zoom out
Zoom in
Previous page
1/65
Next page
17
Assembly Instructions
Remove all the separate parts from the packaging, lay them on
the oor and check roughly that all are there on the base of the
assembly steps. Please note that a number of parts have been
connected directly to the main frame and preassembled. In
addition, there are several other individual parts that have been
attached to separate units. This will make it easier and quicker
for you to assemble the equipment. Assembly time: 30 - 40 min.
Step 1:
Install of front and rear foot (2+3) to the main frame (1).
1. Place two screws (13), washers (14) ), spring washers (30) and
nuts (15) accessibly beside the front and rear parts of the main
frame (1).
2. Insert the foot bars (2+3) in the holder of the main frame (1) and
adjust so that the hole patterns of the holders and the foot bars
(2+3) are aligned. The rear foot has preassembled eccentric caps
(12).
3. Push one screw (13) through each hole.
4. Fit the screw ends of (13) with one washer (14) and one spring
washer (30) each and fasten with a nut (15).
(Note: If the machine has positioned for training on an uneven
oor, this can be compensated at any place by turning the
eccentric caps (12).
Step 2:
Installation of right and left pedal (9R+9L) at pedal crank (10).
1. The pedals are marked “R” for right and “L” for left.
2. Screw the right pedal (9R) into the threaded hole on the right
hand side of the pedal crank (10) and tighten rmly.
(Note: Right and left are species as viewed seated on the
machine during training. It must also be observed that the
threaded part of the right pedal must be screwed clockwise into
the threaded hole of the pedal crank.)
3. Screw the left pedal (9L) into the threaded hole on the left hand
side of the pedal crank (10) and tighten rmly.
(Note: The threaded part of the left pedal have to screw
anticlockwise into the threaded hole of the pedal crank.)
English
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Christopeit CL2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Christopeit CL2 in the language / languages: English, German, Dutch, French, Polish as an attachment in your email.

The manual is 2.56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info