644055

Christopeit AP1 - 1100 Manual

15
Zoom out
Zoom in
Previous page
1/48
Next page
15
English
Assembly Instructions
Remove all the separate parts from the packaging, lay them on the floor
and check roughly that all are there on the basis of the following assem-
bling steps. Please note that a number of parts have been connected
directly to the main frame and preassembled. In addition, there are
several other individual parts that have been attached to separate units.
This will make it easier and quicker for you to assemble the equipment.
Step 1:
Attach the stabilizer (54 + 58) at main frame (26).
1. Attach the front foot (54) with the preassembled transport rollers (53) to
the main frame. Do this with the two screws (56), spring washers (21),
washers (17), and cap nuts (55).
2. Attach the rear foot (58) to the main frame (26). Do this with the four
screws (16), spring washers (21), and washers (42). After assembly has
been completed, you can compensate for minor irregularities in the
floor by turning the wheel at cap (57). The equipment should be set up
that the equipment does not move of its own accord during a training
session.
Step 2:
Attach the front post (13) at main frame (26).
1. Hold the handlebar support (13) with the computer cable (7) against the
main frame holder. Connect the plug for the computer cable (7) coming
out of the bottom of the handlebar support (13) of the computer with
the matching plug for the sensor cable (24) coming out of the main
frame (33). (Note: The computer cable harness (7) projecting from the
support (13) must not slide into the tube, as it is required for later steps
of installation.)
2. Connect the cable of tension control (12) to the bracket of lower section
cable tension (25) (See figure A1-A4). Before this step of the installation,
it is advisable to adjust the resistance setting to the stage, at which the
cable extends furthest from the sheath. Put the lowest part of cable (12)
into the small hook (figure A1). Pull it (figure A2) until the small hook get
in higher position and then insert the cable (12) onto the bracket (25)
(figure A3+4).
3. Place the handlebar support (13) in the locator provided for it in the
main frame (26). Ensure that the cable connections are not squashed.
When putting the steering tube in place, push the former slowly down
into the locator in the main frame. Screw the handlebar support (13)
onto the base frame (26) with the screws (16), spring washers (21) and
washers (17).
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Christopeit AP1 - 1100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Christopeit AP1 - 1100 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info