644071

Christopeit AC5 - 1122A Crosstrainer Manual

15
Zoom out
Zoom in
Previous page
1/44
Next page
15
English
Assembly Instructions
Remove all the separate parts from the packaging, lay them on the floor
and check roughly that all are there on the base of the assembly steps.
Please note that a number of parts have been connected directly to
the main frame and preassembled. In addition, there are several other
individual parts that have been attached to separate units. This will
make it easier and quicker for you to assemble the equipment.
Step 1:
Attach the stabilizer (2+3) at main frame (1).
1. Attach the front foot (2) with the preassembled transport rollers (4) to the
main frame (1). Do this with the two screws M8x75 (7), curved washers
8//20 (8) and spring washers (9).
Attention: Mount the front foot into right direction, so that the transport
rollers don’t touch the floor during exercising.
2. Attach the rear foot (3) with height adjustable foot caps (5) to the main
frame (1). Do this with the two screws M8x75 (7), curved washers 8//20
(8) and spring washers (9). After assembly has been completed, you can
compensate for minor irregularities in the floor by turning the wheel at
cap (5). The equipment should be set up that the equipment does not
move of its own accord during a training session.
Step 2:
Attach the support (17) at the main frame (1).
1. Place screws (13), each washers (9) and spring washers (8) accessibly
beside the front part of the main frame (1).
2. Place the lower end of the support (17) against the main frame (1) and
push the handlebar cover (14) onto the support (17). Plug the ends of
the two computer cable harnesses (12) and (15) projecting from (1) and
(17) together.
(Note: The computer cable harness (15) projecting from the support (17)
must not slide into the tube, as it is required for later steps of installation.)
3. Connect the middle section tension cable (16) to the bracket of lower
section cable tension (11) (See figure A1-A4]). Before this step of the
installation, it is advisable to adjust the resistance setting to the position,
at which the cable extends furthest from the sheath. Put the lowest part
of cable (16) into the small hook of lower tension cable (11) (figure A1).
Pull it (figure A2) until the small hook get in higher position (figure A3)
and then insert the cable (16) onto the bracket (11) (figure A4). When
joining the tubes, ensure that the cable connection is not trapped.
4. Put one spring washer (8) and one washer (9) on each screw (13). Push
the screws (13) through the holes in the support (17), screw into the
threaded holes of the main frame (1) but don’t tighten them firmly. (This
screw connection point will screw tightly at least in Step 4)
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Christopeit AC5 - 1122A Crosstrainer at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Christopeit AC5 - 1122A Crosstrainer in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info