585788
15
Zoom out
Zoom in
Previous page
1/44
Next page
15
English
Assembly Instructions
Before beginning assembly, be sure to observe our recommendations
and safety instructions.
Step 1:
Installation of the front foot bar (33) and rear foot bar (36) at the main
frame (23) with carriage bolts (35+75), washers (17+64) and cap nuts
M8 (38).
1. Place screws (35) and each two flat washers (64), two spring washers
(76) and two nuts (38) accessibly beside the front part of the main frame
(23).
2. Place screws (75) and each two curved washers (17), two spring washers
(76) and two nuts (38) accessibly beside the rear part of the main frame
(23).
3. Insert the foot bars (33+36) into the holder of the main frame (23) and
adjust, so that the hole patterns of the holder and the foot bars (33+36)
are aligned.
4. Push one screw (35 or 75) through each hole.
5. Fit the screw ends of (35 + 75) each with one washer (64 or17) and
fasten with a cap nut (38).
(Note: If the machine is placed for training on an uneven floor, this can
be compensated at any time by turning the rear end caps (37).
Step 2:
Connecting the computer cable harness incl. sensor (22) to the
computer cable harness (2), connection of the cable of the resistance
adjuster (21) with the resistance adjusting unit (20) and installation of
the handlebar support (11) on the main frame (23) with the roundheaded
Allen screws M8x15 (18), spring washers (76) and washers 8//20 (17).
1. Place the lower end of the handlebar support (11) against the main
frame (23). Plug the ends of the two computer cable harnesses (2) and
(22) projecting from (23) and (11) together.
2. Join the two ends of the cables (20) and (21) as indicated in the drawing
(A1-A4).
(Note: Before this step of the installation, it is advisable to adjust the
resistance setting to the highest stage, at which the cable extends
furthest from the sheath. If the factory adjusted pedal resistance range
of the machine should later be found to be too great or too small, this
can be simply adjusted as the cables. For this, loosen nut of cable (21),
turn the threaded piece correspondingly and secure the new position
with nut.
In this respect: The further is screwed into the U-piece, the greater the
resistance, and the converse.)
3. Place the handlebar support (11) in the locator provided for it in the main
fame (23).
(Note: When joining the tubes, ensure that the harness and cable
connections are not trapped.
4. Put one curved washer (17) and one spring washer (76) on each screw
(18). Push the screws through the holes in the support (11), screw into
the threaded holes of the main frame (23) and tighten firmly.
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Christopeit AB 1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Christopeit AB 1 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info