574370
6
Zoom out
Zoom in
Previous page
1/24
Next page
UK
3. Configuring the IRIS Touch Dialler
3.1. Setting the GPRS APN (Ethernet + GPRS only)
Virtually all configurations required for standard operation of the IRIS dialler can be made
via the standard alarm panel keypad, (Texecom or Galaxy). However, if GPRS is to be
used, neither panel currently support configuration of the Access Point Name, so this
must be set up via alternative means as follows:
1. Via a text message to the phone number of the fitted SIM card. The text should be in
the format:
AT%G10=apn’, where ‘apn’ is the APN name, e.g. orangeinternet. The
IRIS dialler will respond with the text message ‘Command accepted’.
2. Via Chiron’s IRIS Dialler Configuration software.
For security reasons, the text message will not be accepted once the IRIS dialler is set up
for communications to the Monitoring Centre, so ensure the IP address of the Monitoring
Centre has not been entered (see below) before sending the message.
3.2. Configuration via Galaxy Keypad
The IRIS dialler emulates a Galaxy Ethernet module and the following parameters should
be set via the keypad menus:
Alarm format.
IP address of Monitoring Centre in Primary IP field.
Account number.
IP address, subnet mask and gateway address (i.e. if fixed IP address required).
No other parameters for the Galaxy Ethernet modules need to be set.
When complete, make a test call and the parameters will be loaded into the IRIS dialler.
3.3. Configuration via Texecom Keypad
The Texecom keypad has a specific menu set for IRIS IP modules. The following
parameters should be set:
IP address of Monitoring Centre for Polling.
Dialler name/account number.
IP port number to be used with Wintex.
3.4.
Post Configuration Checks
Carry out the usual alarm signaling tests to ensure the Monitoring Centre receives the
signals correctly. If GPRS is being used as a backup to Ethernet, disconnect the Ethernet
cable and repeat the tests.
.
2 IRIS Touch 600 Range Dialler Quick Installation Manual (Version 1.0)
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Chiron IRIS Touch 600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Chiron IRIS Touch 600 in the language / languages: English as an attachment in your email.

The manual is 6,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Chiron IRIS Touch 600

Chiron IRIS Touch 600 Installation Guide - English - 25 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info