815477
15
Zoom out
Zoom in
Previous page
1/28
Next page
®
INSTALLATION INSTRUCTIONS
5. SECURE THE CASING TO THE WALL
Secure the casing in the opening by inserting screws, as shown on the
diagram. The stove can be screwed down through the base or through the
sides as required.
6. FILL WITH INSULATION AND MAKE GOOD THE OPENINGS
If you are using the vermiculite method of insulating the convection casing,
pour down from the top of the chimney. Fill in the space between the
casing and the brickwork and around the flue pipe with a vermiculite or
perlite concrete mix (see fig. 12). The recommended mixture is 6 parts of
vermiculite or perlite to 1 part cement. Add only enough water so that a
few drops are released when a handful of the mixture is squeezed.
Make good the opening at the top and sides of the convection casing
ensuring that a good seal is made with the side flanges. It is recommended
to use heat resistant plaster on the wall surrounding the stove.
If for any reason it is not going to be possible to sweep the chimney
through the appliance, a soot door must be fitted.
charnwood
BAY
Attach convection casing to wall by
inserting screws at any of these points
7. SLIDE IN THE STOVE
For the Bay 5GT, remove the RH fan by undoing
the two retaining screws. Move the stove into the
position shown and attach the free wire on the
inside of the convection casing to the pins
marked “pwr” +12V on the circuit board located
below the LH fan. Attach the LH fan wire to the
PCB.
Carefully slide the stove into the convection
casing until the flue outlet lines up with the upper
flue collar and the air inlet engages at the base of
the stove.
15
8. INSERT COACH BOLTS
From the inside of the stove,
insert coach bolts in to slots A
and B so that they hang down
into the stove. These are held in
place by the clips and will secure
the flue collar.
A
B
‘R’ Pin
1.7mm
Washer
M8x17
Roller
Clevis Pin
(welded inside
stove)
ATTACHING THE
ROLLERS
Slot the roller and washer
over the clevis pin. Insert ‘R’
pin through the clevis pin.
9. FIT THE DOOR
Carefully lift the door onto the lower hinge pin and
insert the upper hinge pin through the hinge post
and the door
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Charnwood Bay 5 VL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Charnwood Bay 5 VL in the language / languages: English as an attachment in your email.

The manual is 3.02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info