815477
13
Zoom out
Zoom in
Previous page
1/28
Next page
®
INSTALLATION INSTRUCTIONS
charnwood
BAY
For the UK adaptor this is a 240 volt 50 Hz. a.c. supply. For the
European adaptor this is a 220 volt 50 Hz. a.c. supply. THE MAINS
ADAPTOR MUST BE USED. DO NOT CONNECT A MAINS
SUPPLY DIRECTLY TO THE STOVE.
Plug the connector from the adaptor into the socket on the wire from
the stove. Cable clips or conduit should be used to retain the wire
where necessary. If it is necessary to extend the wire then ensure that
the correct polarity is maintained. The centre pin on the plug must be
positive. There is a thermal cut out linked into the fan control. This
means that the fans will not operate until the stove warms up.
AIR SUPPLY
The fire needs air for combustion, there are various ways of
supplying this, and they must meet the requirements of the building
regulations.
One way of meeting this requirement as outlined in Approved
Document J is to have a permanently open air vent into the room
that the stove is fitted to as per the table below:
If using this method then the air supply ducting may be terminated in
the room, or the ducting connections on the stove can be removed,
13
as detailed in figure 14 so that air is taken from between the fire box
and the convection casing.
Alternatively a fixed ducted air supply method can be used as shown
in fig. 13. One end of the air supply ducting is connected to the stove
and the other is terminated outside. The ducting must be 100mm dia,
non-combustible, less than 5.5m long and must not have more than
five 90° bends and two 45° elbows. It must be sleeved where it
passes through the external wall. The inlet must be permanently open
and the duct free of any constrictions. The inlet must have a suitable
grill to prevent entry by vermin, and should be positioned so that
blockage by leaves or other debris will be avoided. Ensure that rain or
flood water will not enter the duct. A spillage test must be carried out
during commissioning to verify adequate air supply for combustion -
see the section on Commisioning.
External air kits are available, please contact Charnwood for more
information (Ref TIS 120)
Fig. 13 Installation in a standard chimney
Air permeability
m³/(h.m²)
Minimum vent area cm²(in²)
Bay 5GT
Bay 5
Bay VL
>5.0
5.5
(0.9)
not required
not required
<5.0
33
(5.1)
27.5
(4.3)
27.5
(4.3)
Fig 14 Fitting the duct covers
Bay 5 & VL
Bay 5GT
Remove:
Lower Gasket
Upper Inlet Plate
Lower Inlet Plate
Fit the air duct cover
to the outside of the
convection casing
Remove the Inlet Gasket
and Fit the air duct cover
to the outside of the
convection casing.
Remove the inlet gasket
and cover from the air
box.
Lintel
Flexible Flue Liner
Closure plate
Stove
External air kit
to outside wall
Sleeving
External grille
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Charnwood Bay 5 VL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Charnwood Bay 5 VL in the language / languages: English as an attachment in your email.

The manual is 3.02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info