Manual Charlton Jenrick Fireline Woodtec 5 (page 9 of 28) (English)

707656

Zoom out

Zoom in

1/28

8 Woodtec Freestanding Issue 01.1 05/17

Where the chimney is believed to have previously served an open fire installation, it is possible

that the higher flue gas temperature from the stove may loosen deposits that were previously

firmly adhered, with the consequent risk of flue blockage. It is therefore recommended that the

chimney be swept a second time within a month of regular use after installation.

If you have any doubts about the suitability of your chimney, consult your local dealer/stockist

or chimney specialist. If there is no existing chimney then either a solid fuel compatible

prefabricated block chimney or a twin-walled insulated stainless steel flue to BS 4543 can be

used. These chimneys must be fitted in accordance with the manufacturer’s instructions and

Building Regulations.

5.2. Ventilation

Document J of the Building Regulations states that purpose provided ventilation is not required

in England and Wales unless the appliance nominal rated output is greater than 5kW. Over 5kW

5.5 cm

of ventilation (550mm

) is required for every kW output above 5. For example 6.5 kW

requires 8.25 cm

and 8 kW needs 16.5cm

. In any case, if difficulty in starting the fire or any

excessive fuming is experienced, ventilation must be put in place as required to eliminate these

flue problems. If a flue draught stabiliser is fitted then extra ventilation is required. See

Document J of the Building Regulations for detailed guidance especially in new build properties.

A specifically designed direct outside air connection may be used with these stoves to provide

appropriate levels of ventilation (significantly in excess of the above requirements) directly to

the stove and chimney as follows. NOTE: in order to register the installation with HETAS as of

early 2016 certain extra evaluation and checking is required if using an outside air connection. If

the direct air kit is used and no ADJ vent is installed then a direct registration with Building

Control may also be possible.

5.3. Direct Outside Air Connection

These stoves are supplied with the facility of using a dedicated 100mm diameter direct

connection duct through a suitable route to the outside air. It can be connected to the rear of

the stove and should be fitted at the time of stove installation. Only the approved kit for these

stoves should be used. This is designed to supply all the necessary air for safe combustion and

operation of the stove – providing there is no depressurisation of the property by mechanical

or other types of ventilation, the flue, chimney and ventilation duct are working correctly, and

properly maintained clear of obstructions or leaks etc. The kit supplies all the primary,

secondary and tertiary air to the stove and also provides room ventilation in excess of the

Document J Building Regulations during re-fuelling via the air connection unit under the stove

and so subject to no depressurisation (as above) may be used where mechanical ventilation and

heat recovery (MVHR) units are used. Some additional instructions for installation are provided

with the dedicated kit supplied. NOTE: in order to register the installation with HETAS as of 2016

certain extra evaluation and checking is required if using an outside air connection. If the direct

air kit is used and no ADJ vent is installed then a direct registration with Building Control may

also be possible.

5.4. Flue Draught

Typically a flue draught at the flue collar of minimum 2.2mm to a maximum 3.5mm water gauge

(22 to 35 Pascals) is required for satisfactory appliance performance. This relates to 12-25

Pascals at the tapping on EN13240/13229 test rigs. The flue draught should be checked under

fire at high output and, if it exceeds the recommended maximum, a draught stabiliser must be

fitted so that the rate of burning can be controlled to prevent over-firing.

5.5. Connection to the Chimney

This appliance is not suitable for use in a shared flue.

where will i locate the SERIAL No of my WOODTEC 5 wood burner for Warranty MANY THANKS Submitted on 17-5-2022 at 18:18
Reply Report abuse
where will i find the SERIAL No on my WOODTEC 5 for the Warranty many thanks P. Loach Submitted on 17-5-2022 at 18:13
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Charlton Jenrick Fireline Woodtec 5 in the language / languages: English as an attachment in your email.

The manual is 1,82 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Charlton Jenrick Fireline Woodtec 5 Manual

Product: