555430
37
Zoom out
Zoom in
Previous page
1/48
Next page
36
Operation
Using your Garage Door Opener
The garage door opener can be activated through a wall-mounted door control, remote control, wireless
keyless entry or MyQ
®
accessory.
When the door isclosed and the garage door opener is activated the door will open. Ifthe door senses
an obstruction or is interrupted while opening the door will stop. When the door is in any position other
than closed and the garage door opener is activated the door will close.If the garage door opener
sensesan obstruction while closing, the door will reverse.If the obstruction interruptsthe sensor beam
the garage door opener lights will blink 10 times. However,you can close the door if you hold the button
on the door control or keyless entry until the door isfully closed. The safety reversing sensors do not
affectthe opening cycle.
The safety reversing sensor mustbe connected and aligned correctlybefore the garage door opener will
move in the down direction.
Using the Motion Detecting Control Panel
SYNCHRONIZE THE DOOR CONTROL
To synchronize the door control to the garage door opener, pressthe push bar until the garage door
opener activates (itmaytake up to 3 presses). Test the door control bypressing the push bar,each press
of the push bar will activate the garage door opener.
ON (TTC)
OFF (TTC)
Command LED
Motion Sensor
Switch
LIGHT
Button
HOLD OPEN
Button(TTC)
Motion
Sensor
Push Bar
1, 5, and
10 Minute
TTC LED
LEARN Button
LOCK Button
MOTION DETECTING CONTROL PANEL FEATURES
PUSH BAR
Press the push bar to open or close the door.
LIGHTS
Light Button
Press the LIGHT button to turn the garage door opener lights on or off. When the lights are turned on
they will stay on until the LIGHT button ispressed again, or until the garage door opener is activated.
Once the garage door opener is activated the lights will turn offafter the specified period of time (the
factory setting is4-1/2 minutes).The LIGHTbutton will not control the lightswhen the door is in motion.
To change the amount of time the garage door opener lights will stay on:
Press and hold the LOCK button (approximately10 seconds) until the garage door opener lightsflash.
The time interval is indicated by the number times the garage door opener flashes:
l
1 flash is1-1/2 minutes
l
2 flashes is2-1/2 minutes
l
3 flashes is3-1/2 minutes
l
4 flashes is4-1/2 minutes
To cycle through the time intervals repeat the step above.
Light Feature
The lightswill turn on when someone enters through the open garage door and the safety reversing
sensor infrared beam is broken.
l
Deactivate: Press and hold the LIGHTbutton (approximately 10 seconds) until the garage door
opener lightsturn on, then off again.
l
Activate: Startwith the garage door opener lightson. Press and hold the LIGHT button
(approximately 10 seconds) until the garage door opener lightsturn off, then on again.
If the command LED iscontinuously blinking, the LOCK feature needs to be deactivated.
37


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Chamberlain LW5000EV at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Chamberlain LW5000EV in the language / languages: English as an attachment in your email.

The manual is 5,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info