666997

Celestron SkyProdigy 6 - 11076 Manual

7
Zoom out
Zoom in
Previous page
1/32
Next page
ASSEMBLY
SkyProdigy comes partially assembled and can be operational in
a matter of minutes. SkyProdigy is conveniently packaged in one
reusable shipping carton that contains the following accesso-
ries:
t NNBOENN&ZFQJFDFTow
t w4UBS%JBHPOBM
t 4UBS1PJOUFS'JOEFSTDPQFBOE.PVOUJOH#SBDLFU
t %FMVYF"DDFTTPSZ5SBZ
t 5IF4LZ9'JSTU-JHIU"TUSPOPNZ4PGUXBSF
t $PNQVUFSJ[FE)BOE$POUSPM
Assembling SkyProdigy
Your SkyProdigy comes in three major sections: the optical tube,
fork arm and tripod. These sections can be attached in seconds
using the quick release coupling screw located under the tripod
mounting platform and the dovetail mounting clamp located on
the inside of the fork arm. To begin, remove all of the accessories
from their individual boxes. Remember to save all of the contain-
ers so that they can be used to transport the telescope. Before
attaching the visual accessories, the telescope tube and fork arm
should be mounted to the tripod. First, install the accessory tray
onto the tripod legs:
1. Remove the tripod from the box and spread the legs apart
until the center leg brace is fully extended.
2. Locate the accessory tray, and place it on top of the tripod
center support brace in between the tripod legs
(see gure 2-1).
3. Rotate the accessory tray so that the central hole in the tray
slides over the ange post in the center of the support
bracket.
4. Finally, rotate the tray so that the locking tabs slide under the
locking clips on the support bracket. You will hear the tray
snap into place.
It is a good idea to level the tripod and adjust the height of the tripod
legs before attaching the fork arm and tube. Minor adjustments can
be made later. To adjust the height of the tripod legs:
1. Loosen the tripod leg locking bolt located on the side of
each leg.
 4MJEFUIFJOOFSQPSUJPOPGFBDIMFHEPXOwUPwJODIFT
3. Adjust the tripod height until the bubble level on the tripod
leg is centered (See gure 2-2).
4. Tighten the tripod locking bolts to hold each leg in place.
Attaching the Hand Control Holder
SkyProdigy comes with a snap-on hand control holder that con-
veniently attaches to any of the tripod legs. To attach the hand
control holder simply position the holder with the square plastic
tab facing up and push against the tripod leg until it snaps into
place (See gure 2-3).
Attaching the Fork Arm to the Tripod
With the tripod properly assembled, the telescope tube and
fork arm can easily be attached using the quick release coupling
screw located underneath the tripod mounting platform:
1. Place the fork arm base inside the tripod mounting platform.
2. Thread the coupling screw into the hole at the bottom of the
fork arm base and hand tighten (See gure 2-4).
INSTRUCTION MANUAL [Continued]
FIGURE 2-1
Flange Post
Locking Tabs
Locking
Clips
FIGURE 2-2
Leveling Tripod
FIGURE 2-3
FIGURE 2-4
Tripod
Mounting
Platform
Coupling
Screw
Fork Arm Base
7
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Celestron SkyProdigy 6 - 11076 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Celestron SkyProdigy 6 - 11076 in the language / languages: English as an attachment in your email.

The manual is 3,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info